Mentor II

Chia sẻ: Van Kent Kent | Ngày: | Loại File: PDF | Số trang:8

1
127
lượt xem
28
download

Mentor II

Mô tả tài liệu
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

DC drives are widely used in applications that require regeneration, precise speed control, dynamic performance, and constant torque over wide speed ranges. The Mentor II delivers the universal DC drive solution. Simple stand-alone applications are easily configured to control motor speed, voltage or current using standard internal settings. Set-up is convenient using the drive keypad, CTKP remote keypad, or MentorSoft, a Windows based drive configuration tool. The Mentor II has extensive diagnostic and communication abilities that enhance system reliability. The drive’s standard yet powerful microprocessor is a versatile system component that can eliminate the need for a PLC with integral...

Chủ đề:
Lưu

Nội dung Text: Mentor II

  1. www.emersonct.com Mentor II The Intelligent Drive Overview DC drives are widely used in applications that require regeneration, precise speed control, dynamic performance, and constant torque over wide speed ranges. The Mentor II delivers the universal DC drive solution. Simple stand-alone applications are easily configured to control motor speed, voltage or current using standard internal settings. Set-up is convenient using the drive keypad, CTKP remote keypad, or MentorSoft, a Windows based drive configuration tool. The Mentor —Extrusion II has extensive diagnostic and communication abilities that enhance system reliability. The drive’s standard —Intelligent yet powerful microprocessor is a versatile system component that can eliminate the need for a PLC with integral functions such as thresholds, timers and logic gates that perform basic control. The simple addition of the MD29, a 32-bit Mentor II application coprocessor card, provides high performance drive systems with local intelligence for true distributed control. The MD29 enables users to incorporate custom or proprietary process control application programs to their drive. The Mentor II also provides a wide range of communication protocol options. Mentor II systems have proven to be extremely reliable and are ideally suited to web handling, winders, slitters, extruders, wire drawing, converting lines, and Microprocessor Based Digital DC Drive plastics production. The Mentor II’s integrated design 5 to 1000 HP, 3 phase, 208 to 660 VAC and highly programmable features make it an ideal Regenerative and non-regenerative models choice for OEMs and System Integrators, as well as replacement or retrofit drives for End Users. RS485 serial communications Extensive fieldbus communication capabilities Plug-in 32-bit application coprocessor card (MD29) MentorSoft Windows-based drive configuration tool Complete Motor Solutions 9002 O IS AL AP Digital Drive V PRO 98
  2. 1-800-893-2321 Feature Ratings: Mentor II Performance Advantage THREE PHASE INPUT 3 to 500 HP (208-230 VAC) Accepts wide range of supply voltage (208 to 660 VAC) 5 to 1000 HP (380-460 VAC) Can be applied to worldwide voltages Special Order (525 / 660 VAC), Models M350(R)–M1850(R) only) Non-regen and regen models share the same footprint 208 / 240 VAC Allows for common mechanical design and Motor HP Output Output Field Non-Regen Regen mounting Current Current Output Catalog Catalog (A) (A) Current Number Number MentorSoft Windows based drive configuration tool (@40°C) (@55°C) Provides easy programming and diagnostics 3-7 25 20 M25-14M M25R-14M of the drive 7.5 - 10 45 38 M45-14M M45R-14M 8A 15 75 55 M75-14M M75R-14M 32-bit application coprocessor card (MD29) Current 20 - 35 105 89 M105-14M M105R-14M Enables customized applications for distributed Regulated 30 155 125 M155-14M M155R-14M control system architectures 40 - 50 210 172 M210-14M M210R-14M 75 350 255 M350-14M M350R-14M Profibus-DP, Modbus+, Modbus RTU, Interbus-S, DeviceNet, 10A 100 420 338 M420-14M M350R-14M and CTNet plug-in communication cards Fixed 125 550 428 M550-14M M550R-14M Voltage Communicates on user’s preferred network 150 700 508 M700-14M M700R-14M ➀ 200 825 675 M825-14M M825R-14M Built-in RS485 serial communications 250 900 820 M900-14M M900R-14M 20A Fixed Allows for easy programming and control of drive 300 - 350 1200 1150 Voltage M1200-14M M1200R-14M 400 - 500 1850 1620 ➀ M1850-14M M1850R-14M Extensive and configurable analog and digital I/O Customizes drive to specific applications 380 / 480 VAC Mentor II Programmable boolean logic (AND, NAND, OR, NOR) Motor HP Output Output Field Non-Regen Regen gates with delay outputs Current Current Output Catalog Catalog (A) (A) Current Number Number Assists with general system interface logic needs, (@40°C) (@55°C) expanding application possibilities 5 - 10 25 20 M25-14M M25R-14M 15 - 20 45 38 M45-14M M45R-14M Programmable threshold comparators 8A 25 - 30 75 55 M75-14M M75R-14M Expands application possibilities by providing a pair Current 40 - 50 105 89 M105-14M M105R-14M of independent numerical comparators with Regulated 60 - 75 155 125 M155-14M M155R-14M adjustable hysteresis 100 210 172 M210-14M M210R-14M 150 350 255 M350-14M M350R-14M Built-in digital lock function for frequency following 10A 200 420 338 M420-14M M350R-14M Allows accurate master/slave applications Fixed 250 550 428 M550-14M M550R-14M Voltage 300 700 508 M700-14M M700R-14M Accepts DC tachometer and encoder feedback ➀ 400 825 675 M825-14M M825R-14M Enables precise speed control 500 900 820 M900-14M M900R-14M 20A Fixed 600 - 700 1200 1150 Voltage M1200-14M M1200R-14M Extensive diagnostics and fault indicators 800 - 1000 1850 1620 ➀ M1850-14M M1850R-14M Used for accurate drive system diagnosis ➀ For field control, add external field regulator P/N 9500-9035. Order String M XXX R - 14M Factory Assigned Regen (omit for Non-regen) Output Current Mentor II Product Family 99
  3. www.emersonct.com Terminal Diagram: Mentor II , (300mA max.) Mentor II Terminal Description Pin# Function Type/Description Notes Pin# Function Type/Description Notes 1 +10 VDC Reference Supply 10 mA max 20 0V Common Circuit Common 2 -10 VDC 21 F1 (Run Permit) Digital Input +24 VDC, 10k Ohms 3 Speed Reference Analog Input, 12 bit ±10 VDC, 100k Ohms or 22 F2 (Inch / Jog Reverse) 4-20 mA, 100 Ohms 23 F3 (Inch / Jog Forward) 4 Analog Input # 1 24 F4 (Run Reverse (latched)) 5 #2 Analog Input 25 F5 (Run Forward (latched)) 6 #3 Bi-polar, 10 bit + sign ±10 VDC, 100k Ohms 26 Digital Input F6 Digital Input +24 VDC, 10k Ohms 7 #4 27 F7 8 Motor Thermistor Analog Input 3k Ohms trip point, 28 F8 1.8k Ohm reset level 29 F9 9 DC Tachometer (-) Analog Input 30 F10 10 DC Tachometer (+) Circuit Common 31 Drive Enable Digital Input 30 mSec inhibit delay 11 Armature Current Image Analog Output 6.6 VDC @ 150% 32 Reset Digital Input Fault Reset current 33 +24 VDC Supply User Supply 200 mA max 12 Analog Output # 1 34 Form C Status Relay Relay Common 13 #2 Analog Output ±10 VDC, 5 mA 35 (Zero Speed) N. C. Contact 110 VAC, 5A resistive 14 #3 Bi-polar, 10 bit + sign 36 N. O. Contact 15 Digital Output # 1 37 Form C Status Relay Relay Common 16 #2 38 (Drive Ready) N. C. Contact 110 VAC, 5A resistive 17 #3 Digital Output +24 VDC, 100 mA 39 N. O. Contact 18 #4 Open Collector 40 0V Common Circuit Common 19 #5 Programmable Analog Programmable Digital All Analog I/O is scaleable 100
  4. 1-800-893-2321 Specifications: Mentor II Power Supply Internal power supply out of tolerance Serial Communications Mode 3 serial comms data loss Environment Loss Ambient Operating 0 to 40°C (32 to 104°F) Processor 1 Main control processor fault Temperature Derate current 1.5% per °C to 55°C (32 to131°F) Watchdog Trip Cooling Method Convection and forced convection, model Processor 2 Second control processor fault (MD29) dependent Watchdog Trip Humidity 95% non-condensing at 40°C (104°F) Hardware Fault Hardware malfunction on control board Storage Temperature -40 to 55°C (-40 to 131°F) Memory Fault Stored parameter checksum fault Altitude 0 to 4000m (13,120 ft). External Trip User interlock fault (programmed) Derate 1% per 100m (328 ft) between 1000m Software Fault (A29) MD29 software fault (3,280 ft) and 4000m (13,120 ft). Enclosure Chassis (IP00) Approvals & Listings UL, cUL File #E58592 Vol. 5C Section 1 AC Supply Requirements CE Designed for marking Voltage 208 to 480 VAC -5%, +10% ISO 9002 Certified Manufacturing Facility 525/575/660 VAC ±10% (Optional M350 and above) Phase 3Ø Frequency 45 to 62 Hz Efficiency 98% Dimensions Control Feedback Methods Armature Voltage (resolution .83 volts) DC Tachometer (resolution 0.1%) Encoder (resolution .01%) Field Control Current regulated 8 Amps max (M210/M210R and smaller) Mentor II Voltage regulated .675 or .9 X Line-to-line MO DE ▲ ▲ PA RA ME voltage (M350/M350R and larger) TE ▲ R DA TA Dri ve Ala Read rm y Ze ro Ru speed ▲ n for PA Ru wa n rev rd RA Bri ME dg erse TE Bri e 1 R IN dg At e 2 Analog Input Resolution 12 bit (Qty 1), 10 bit (Qty 4) DE sp X Cu eed rre nt lim it RE SE T Serial Communications 4-wire RS422 or RS485, optically-isolated Protocol is ANSI x 3.28-2.5-A4 Baud rate is 4800 or 9600 Protection AC Line 180 VAC Undervoltage Trip MOV Voltage Input transient suppression Transient Protection Instantaneous 300% armature current Overcurrent Trip Armature Open Circuit Armature circuit is open Catalog Number Size* (in.) Approx. HxWxD Weight (lbs.) Drive Overload Trip Inverse time, 150% for 30 seconds M25-14M thru M75-14M 15 x 10 x 6 22 Phase Loss Trip Loss of input phase M25R-14M thru M75R-14M 15 x 10 x 6 24 Overtemperature Trip Heatsink exceeds 100°C (212°F) M105-14M thru M210-14M 15 x 10 x 8 31 Motor Thermal Trip Motor over-temp switch or Thermistor M105R-14M thru M210R-14M 15 x 10 x 8 33 Feedback Loss Loss of motor feedback M350-14M thru M420-14M 16 x 18 x 11 48 Feedback Reversal Tachometer or Encoder wired backwards M350R-14M thru M420R-14M 16 x 18 x 11 51 Field Loss No field current M550-14M thru M825-14M 17 x 18 x 11 59 Field On Field current during auto-tune M550R-14M thru M825R-14M 17 x 18 x 11 66 Field Overcurrent Field current greater than field demand M900-14M thru M1850-14M 41 x 18 x 20 154 Current Loop Loss Loss of 4-20 mA reference M900R-14M thru M1850R-14M 61 x 18 x 20 264 External Power Supply Short circuit on +24 VDC user power supply * Approximate, not to be used for construction purposes. 101
  5. www.emersonct.com Mentor II Application Cards (MD29 & MD29AN) Options / Software / Accessories The MD29 (9729-9000) and MD29AN application cards contain a high-speed microprocessor which provides a low-cost facility for a system designer to Network Communication Cards write application specific programs without needing a PLC or other stand-alone controller. The add-on cards The fieldbus interface cards provide high-speed fit into a 40-pin header within the Mentor II drive. It communications using the popular networks and is programmed (via the RS232 port) using our Control protocol. These networks allow large amounts of data Techniques SyPT (System Programming Toolkit) that to be transferred quickly to and from network nodes. complies with IEC1131-3 Ladder / Function Block or The RS485 channel is optically isolated (CTNet is DPL (Drive Programming Language). In addition to transformer isolated) for added protection. the application coprocessor, the MD29AN CTNet card supports peer-to-peer cyclic and broadcast messaging at rates up to 5Mbaud. Communication Interface Module System Protocol Catalog Number Configuration The application cards use dual port RAM to provide Profibus-DP MD-24 Master / Slave intimate high-speed bi-directional access. They can read Interbus-S MDIBS Master / Slave and modify any parameter within the drive, enabling CTNet* MD-29AN* Peer-to-peer customized real-time calculations under a multi-tasking DeviceNet MD-25 Master / Slave Modbus RTU* 9729-9000* Master / Slave run-time environment. The Intel i960 32-bit RISC Modbus+ 9500-9100 Master / Slave processor and 256K of user program FLASH memory * CTNet and Modbus RTU cards contain full coprocessor ability. (equivalent to >2000 lines of ladder logic or basic Refer to the Application Cards (MD29 and MD29AN) for more information. instruction code) provide a powerful base for a designer Mentor II to accomplish complex algorithms for demanding time- critical process control. Network Communications The optically isolated RS485 channel serves as a communication port for our CTIU operator interface units. It is fully configurable, supporting multiple communication modes including an ANSI 2 or 4-wire protocol at data rates up to 38.4kbaud. A Modbus protocol with RTU and ASCII slave modes is also available. 32-bit coprocessor (MD-29) ....................9729-9000 32-bit coprocessor with CTNet .......MD29AN-RevD* *RevD for current product, see page 148 for details. Pre-configured Application Programs* Catalog Number S-ramp accel / decel profiling 9729-9001 Digital lock with adjustable ratio control 9729-9002 Spindle orientation 9729-9003 Constant tension, center wind (CTCW) 9729-9004 PID control for load cell tension or dancer position 9729-9005 CTNet Power calculations 9729-9006 Dual Mode Winder 9729-9008 * Contact Control Techniques for detailed information. 102 MD-29 MD-29AN
  6. 1-800-893-2321 Mentor II Operator Interfaces PC to Drive Accessories Universal Keypad (CTKP) Drive Configuration Tool (MentorSoft) The CTKP Universal Keypad is an ideal maintenance tool for use with MentorSoft is a complimentary Windows based drive CT’s digital drives (SE, Unidrive, configuration tool designed to enable the complete Mentor II, Quantum III) and option control and display of all parameters within a Mentor II. modules (UD7X, MD series). Five Functions within MentorSoft allow data to be uploaded, navigation keys and plain text viewed and saved or retrieved from disk, modified and parameter descriptions make the printed. It can be used off-line in the office or on-line CTKP easy to use for viewing and on the plant floor. MentorSoft communicates with modifying drive data. The keypad is designed for hand- the Mentor II via the computer’s serial port to the held or panel mounting. The IP65 rating, screw-down drive’s RS485 port using a communications cable terminals and stress relief for cable connections assure a (CTD-PC-485-XXX). (XXX = ft.) rugged and robust design. Some of its many capabilities include: For more information, refer to the Accessories Section on page 154. Commissioning screen – displays wiring and control logic Operator Interface Unit (CTIU) Compare functions – compares current drive configuration with previously stored versions User screen – customized by the user with up Mentor II to 15 key parameters Built-in reference manuals and search functions – provide extensive “Help” files for both the drive and the software For more information, refer to the Accessories Section on page 138. The CTIU operator interface units incorporate a back-lit LCD display and five easy-to-use navigation keys. Using the intuitive “WYSIWIG” page editor, they can be programmed to display a variety of menus, submenus, alarms, fault conditions and other critical information. The CTIUs support a range of capabilities including multiple font sizes, real time trends and graphs, scheduling and background programs. They communicate via 2 or 4-wire RS485 and to simplify installation, CTIUs are rated NEMA 4/12 and require no screw mounting holes. For more information, refer to the Accessories Section on pages 152-53. 103
  7. www.emersonct.com Mentor II Field Regulators (FXM Family) The FXM family Remote I/O (I/O Box) of field regulators is designed to control The I/O Box expands the I/O capabilities of the the field current of Mentor II and Quantum III drives. The I/O Box is DC motors up to 90 connected to the drive through the MD29 / AN amps. When used application card using an optically isolated RS485 in conjunction with serial link. either the Mentor II or Specifications Quantum III variable speed DC drives, the field regulator is controlled directly Voltage 110 to 240 VAC ±10% via the drive parameters. This allows full customization Frequency 48 to 62 Hz of the field control for any application. The FXMs can Phase 1Ø also be used as stand-alone units when retrofitting existing applications. RS485 Interface Supports binary protocol at data rates up to 38.4kbaud for connection to a The field regulators are single phase, controlled single drive. thyristor rectifier bridges with a control logic PC board. The bridge can be configured by jumpers to operate in half (single quadrant) or full (two quadrant) control mode. The FXMs may be independently controlled by an Mentor II external reference, or set for automatic field weakening (constant horsepower) or constant field current. Field economy control via contact or logic input and a field loss relay for protection are provided for stand-alone operation. The unit also has a bar graph display (10% increments of the selected range) for field current magnitude. Qty Type / Description Notes Catalog Current Frequency Input Voltage Output Voltage* 1 Analog Input (12 bit) ±10 VDC, 100k Ohms or Number (A) (Hz) (VAC) (VDC) 4-20 mA, 100 Ohms 9500-9035 20 50 220 / 380 / 440 198 / 342 / 396 4 Analog Input (10 bit) ±10 VDC, 100k Ohms 60 240 / 480 216 / 432 3 Analog Output (10 bit) ±10 VDC, 5 mA 9500-9032 50 50 220 / 380 / 440 198 / 342 / 396 8 Digital Input +24 VDC, 10k Ohms 60 240 / 480 216 / 432 8 Digital Output +24 VDC, 100 mA 9500-9033 90 50 220 / 380 / 440 198 / 342 / 396 (200 mA total for all outputs) 60 240 / 480 216 / 432 * Maximum output voltage equals 90% of input RMS line voltage. Field current is the controlled variable. 104
  8. 1-800-893-2321 Mentor II Warranty Extended Warranty Critical Components An industry-leading two-year warranty is standard for Mentor II drives. An extended warranty is available that increases the warranty period to five years. Mentor II Model Catalog Number M25 M25WE Minimize Your Machine Downtime Delays M45 M45WE M75 M75WE All too often, spare parts are over looked which results M105 M105WE in a panic search, no less the possibility of costly Next M155 M155WE Day shipping expenses. Having these items on hand can M210 M210WE reduce the associated stress of machine downtime. To M350 M350WE M420 M420WE facilitate this effort, Control Techniques has assembled M550 M550WE several levels of Critical Component kits to fit within M700 M700WE your maintenance budget constraints. These pre- M825 M825WE assembled kits represent a significant savings over M900 M900WE purchasing the same items separately. M1200 M1200WE M1850 M1850WE Mentor II Drive Frame Kit Cat. No. Description Size M25 – M210 M25-210-SP 1 – MDA1 Control board (non-regen 1 – MDA2B Interface board and regen) 6 – Power board fuses M350 – M825 M350-825-SP 1 – MDA1 Control board (non-regen 1 – MDA2B Interface board and regen) 6 – Fuses for MDA5 Filter board 6 – Fuses for MDA6 Power board M900 – M1850 M900-1850-SP 1 – MDA1 Control board (non-regen) 1 – MDA2B Interface board M900R – M1850R M900R-1850R-SP 1 – SCR heatsink assembly (regen) 6 – 6A fuses for MDA6 board 2 – 2A fuses for SD1 board 2 – 30A fuses for SD1 board 105
Đồng bộ tài khoản