Nghệ thuật xếp hình Nhật Bản:goldfish-ranchu

Chia sẻ: Minh Tuan | Ngày: | Loại File: PDF | Số trang:6

0
74
lượt xem
18
download

Nghệ thuật xếp hình Nhật Bản:goldfish-ranchu

Mô tả tài liệu
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình: goldfish-ranchu. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:
Lưu

Nội dung Text: Nghệ thuật xếp hình Nhật Bản:goldfish-ranchu

  1. Ranchu (Ornamental Goldfish) c Ronald Koh - 1994 1. 2. 3. A 12 to 15 cm square of Fold and unfold vertically, Fold to the mark made in paper will do nicely. Fold creasing the centre only. step 2 and unfold, creasing in in half and unfold. the centre only. 4. 5. 6. ... then fold down again. 7. Fold and unfold again as Bring the bottom edge of shown. This marks an the paper to the crease eighth of the height. made in step 4 ... Fold and unfold each 8. 9. corner, creasing well. 10. Inside reverse fold along Turn paper over. creases made in step 7. Fold down ... 11. 12. 13. ... and again on the right. Turn over again Fold the diagonal edges of the paper to the line in the middle, crease firmly, and unfold.
  2. 14. 15. Bring down this layer ... ... like this, then rabbit,s ear both sides along creases made previously. 16. 17. 18. 19. Turn over. Open out this Lift out the hidden Fold up the lower portion of layer to the right. paper at the top, the assembly as shown. then open out the layer on the left. 20. 21. 22. Valley fold ... ... then crimp fold each Fold assembly in half while side. lifting out the layer at the top and a triangle at the bottom ... 23. 24. 1/4 25. ... like this ... ... and this. Fold the first two flaps to the Rotate the right, and crease firmly. model
  3. 26. 27. 28. Now valley fold ... ... then unfold Steps 25 and 26. Lift up the first layer ... 29. 30. 31. ... then fold in the left corner Fold the next layer on the left ... then bring down the top flap as along creases made in to the right as illustrated ... you valley fold the assembly on Step 26. the left along creases made in Step 25 ... 32. 33. 34. ... like this. Fold down the first layer ... ... then reverse fold the Repeat Steps 25 to 31 on the resulting corner as other side. shown. 35. 36. 37. Bring up the top layer again ... ... then valley fold the next ... and then valley fold again layer ... and crimp as illustrated.
  4. 38. 39. 40. Now bring down the layer at Crimp fold according to ... and unfold. the top again and repeat diagrammed proportions, Steps (?) to 37 on the other crease firmly ... side. 41. 42. 43. Bring up the top layer again. Crimp fold each of the four Fold up as shown ... layers separately as shown, then close the assembly by bring the top layer down again. 44. 45. 46. ... then down again. ... then crimp fold as Now open out to unfold Repeat at the back from illustrated. Steps 43 to 45. here through Step 47 ... 47. 48. 49. Collapse the assembly Your model should now ... and yet again. under the body as shown, look like this. The illustration is using crease lines made Valley fold, creasing slightly enlarged from previously. firmly ... here on.
  5. 50. 51. ... and yet again. Now unfold Steps 49 and 50. 52. 53. Hidden between the external body layers ... like this. are two narrower pleated layers. Push up Now crimp fold both sides of the from the bottom to open out the pleat of head along creases made the hidden layer nearest to you, while previously while bringing out the simultaneously separating the first and top of the head ... second layers at the top ... 55. 56. 54. Crimp fold both sides of the model Fold and unfold at the top of Now sink at the top of the to form the mouth. the head, creasing firmly. head, then continue folding Mountain fold at the base of as illustrated. the neck. 57. 58. 59. Valley fold to the left again ... ... then unfold Steps 56 and 57. Separate the two layers of this flap and crimp fold along creases made previously.
  6. 60. 61. 62. Sink the little corner at the Mountain fold twice as illustrated. Valley fold the next layer. bottom. The upper fold should automatically Diagrams 61 and 62 shows form a hidden gusset. a close up of this part of the model. 63. 64. Mountain fold under and repeat from Step 56 on the other side of the head. Crimp fold each of the two fins to bring them a little further to the back. Shape the central area of each side of the tail as illustrated. 65. Finally, crimp fold both sides of the body along creases made previously, making sure that the body convexes outwards.
Đồng bộ tài khoản