Configuring a catalyst switch

Xem 1-16 trên 16 kết quả Configuring a catalyst switch
  • Upon completing this lesson, you will be able to: Verify the default configuration of the device, given a functioning access layer switch Configure the switch management IP address and the default gateway, given a functioning access layer switch and an IP addressing scheme Execute an add, move, or change on an access layer switch, given a new network requirement

    ppt26p trinhvang 25-01-2013 19 4   Download

  • After studying this chapter you will be able to understand: Initial startup of the Catalyst Switch, initial bootup output from the Catalyst 2960 Switch, initial configuration of the Catalyst 2960 Switch using setup, logging in to the Switch and entering the privileged EXEC mode,...

    ppt19p youcanletgo_02 07-01-2016 7 1   Download

  • The Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide is for the network manager responsible for configuring the Catalyst 2900 series XL and Catalyst 3500 series XL switches, hereafter referred to as the switches. Before using this guide, you should be familiar with the concepts and terminology of Ethernet and local area networking. This guide provides information about configuring and troubleshooting a switch or switch clusters.

    pdf360p phongthinh 07-08-2009 112 35   Download

  • Upon completing this module, you will be able to: Explain how bridging and switching operates Explain the purpose and operations of the Spanning-Tree Protocol Verify the default configuration of the device, given a functioning access layer switch Build a functional access switch configuration to support the specified network operational parameters, given a network design Execute an add, move, or change on an access layer switch, given a new network requirement

    ppt15p trinhvang 25-01-2013 23 4   Download

  • After studying this chapter you should be able to: Understand high availability, implement high availability, describe high availability monitoring options, describe switch supervisor redundancy, describe gateway redundancy protocols, configure and verity Cisco IOS server load balancing.

    ppt134p kiepnaybinhyen_02 29-12-2015 5 2   Download

  • Topics covered in this chapter include the following: An introduction to fundamental switching concepts, starting with the building blocks of VLANs and trunking; an introduction to other building blocks of switching technology, including Spanning Tree Protocol for high availability; a revisit and further explanation of security threats that exploit vulnerabilities in the switching infrastructure;...

    ppt36p kiepnaybinhyen_02 28-12-2015 12 1   Download

  • In this chapter, you learned to: Explain the role of VLANs in a converged network, explain the role of trunking VLANs in a converged network, configure VLANs on the switches in a converged network topology, troubleshoot the common software or hardware misconfigurations associated with VLANs on switches in a converged network topology.

    ppt20p youcanletgo_01 29-12-2015 3 1   Download

  • This chapter presents the basics of configuring the 1900 and 2950 Catalyst switches as well as Cisco routers. As you continue throughout this book, you will build upon these fundamental and important concepts for accessing, configuring, and managing your Cisco devices. I am making the assumption that you have never configured a Cisco device before and therefore will begin with the very basics by explaining the operating system that these devices use, the advantages that Cisco’s operating system provides, and how to use some basic operating system commands to configure your Cisco device....

    pdf71p vinhnghi 27-08-2009 82 25   Download

  • VLAN Trunk Protocol (VTP) reduces administration in switched networks. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain. This reduces the need of configuring the same VLAN everywhere. VTP is a Cisco-proprietary protocol that is available on most of the Cisco Catalyst Family products. In this lab you will troubleshoot some basic VLAN trunking problems with VTP (VLAN Trunking Protocol).

    pdf1p laquang 28-08-2009 84 9   Download

  • This lab provides a scenario on troubleshooting Inter-VLAN routing with a Route Switch Module (RSM) on a Catalyst family switch. When it comes to troubleshooting the RSM, the first thing to do is to think of it as a simple external router. It is very seldom that a RSM specific issue is causing a problem when Inter-VLAN routing is concerned. Therefore, two main areas where this could occur are RSM hardware related issues or Inter-VLAN configuration specific issues (mostly related to the interaction between routers and switches)....

    pdf1p thutrang 28-08-2009 49 5   Download

  • Your network is growing. You have out grown your 2900 and need to add more port capacity. As time goes on, your plan is to continue to add Catalyst 2900 switches in your IDFs. At this point you are adding a Catalyst 4000 in your MDF to tie all of these 2900s together. In order to make adds/moves/changes easier to manage, you will configure VLANs throughout your entire network. The 4000 will be at the core of this switch configuration.

    pdf1p laquang 28-08-2009 287 59   Download

  • This lab is designed to walk you through a basic VLAN configuration using two Catalyst 1900 (or 2820) series switches. This lab shows you step-by-step what commands to type in and how to check that you have configured things correctly. Each switch must be configured with the Enterprise edition software. The Cisco IOS software CLI is not available if the switch has been configured with the Standard edition software.

    pdf1p trungha 28-08-2009 179 49   Download

  • You have just purchased a new Catalyst 4000 Ethernet switch with a supervisor module and a 32 port layer 3 switch module. Configure the supervisor module so that it has a name, IP address, and basic password security using the Command Line Interface (CLI).

    pdf1p laquang 28-08-2009 54 3   Download

  • You have just taken a job at a company that uses Catalyst 4000 Ethernet switches for their backbone. You want to save a copy of the configuration file from your Catalyst 4000 switch to a TFTP server for safekeeping.

    pdf1p laquang 28-08-2009 45 3   Download

  • You have just taken a job at a company that uses Catalyst 2900 Ethernet switches in their IDFs. You want to save a copy of the configuration file from your Catalyst 2900 switch to a TFTP server for safekeeping.

    pdf1p laquang 28-08-2009 49 3   Download

  • Cable a network similar to the one in the diagram. The configuration output used in this lab is produced from a 2950 series switch. Any other switch used may produce different output. The following steps are to be executed on each switch unless specifically instructed otherwise. . Instructions are also provided for the 1900 Series switch, which initially displays a User Interface Menu. Select the “Command Line” option from the menu to perform the steps for this lab. Start a HyperTerminal session. Note: Go to the erase and reload instructions at the end of this lab.

    pdf7p thanhha 27-08-2009 41 2   Download

Đồng bộ tài khoản