Enabling ospf

Xem 1-8 trên 8 kết quả Enabling ospf
  • Upon completing this lesson, you will be able to: Describe the features and operation of OSPF Use Cisco IOS commands to configure dynamic routing for a single area OSPF network, given a functioning router Use show and debug commands to identify anomalies in dynamic routing operation using OSPF, given an operational router

    ppt15p trinhvang 25-01-2013 16 7   Download

  • In this lab, you configure OSPF on three Cisco routers. First, you configure loopback interfaces to provide stable OSPF Router IDs. Then you configure the OSPF process and enable OSPF on the appropriate interfaces. After OSPF is enabled, you tune the update timers and configure authentication.

    pdf6p laquang 03-09-2009 75 19   Download

  • On each router, create an OSPF process that puts each interface into area 0.0.0.1. I strongly recommend that you have one network statement for each interface, but you can experiment with wildcards that put more than one interface into OSPF. It is your choice whether to advertise the loopback subnets. You may choose to enable OSPF debugging and watch the activity as OSPF initializes. With increasing numbers of routers, you will have more and more debug traffic -- you have been warned! Simply record the traffic for later analysis; it will go by too fast to review on the screen....

    pdf1p trungha 28-08-2009 51 7   Download

  • - Step 2: Xóa bỏ OSPF trên các router PE liên quan và cấu hình BGP neighbor với mỗi router CE và các router PE. - Step 3: Bởi vì cả hai site của khách hàng của bạn cùng chỉ số AS, nên bạn cần enable tính năng AS-override trên các router PE.

    pdf8p phuochau17 16-05-2011 81 19   Download

  • Basic router config for R1, R2, R3 and ISP: Password for console=cisco Password for enable mode=ccna Password for vty =class 4. Install OSPF as the routing protocol on R1,R2 and R3. DO NOT advertise all subnets to the ISP router: process number = 10, area number=0 ) 5. Configure the static route on R1,R2 and R3 for the Internet connection

    pdf1p phutran76 16-07-2012 56 15   Download

  • For organizations looking to implement scalable, fault-tolerant, secure networks, the Advanced Networking blade enables them to run industry-standard dynamic routing protocols including BGP, OSPF, RIPv1, and RIPv2 on security gateways. OSPF, RIPv1, and RIPv2 enable dynamic routing over a single autonomous system—like a single department, company, or service provider—to avoid network failures.

    pdf495p hoangtumayman 26-09-2011 34 13   Download

  • Part I: 1. Cabling as the diagram 2. Calculating all the subnets for the diagram. Note: 172.X.0.0/16 where X is the sequence number in the students list. 3. Basic router config for R1, R2, R3 and ISP: Password for console=cisco Password for enable mode=ccna Password for vty =class 4. Install OSPF as the routing protocol on R1,R2 and R3. DO NOT advertise all subnets to the ISP router: process number = 10, area number=0 ) 5. Configure the static route on R1,R2 and R3...

    pdf1p anhchangxuixeo1002 14-03-2013 40 5   Download

  • Sample Configuration for Authentication in OSPF Document ID: 13697 Introduction Prerequisites Requirements Components Used Conventions Background Information Configure Network Diagram Configurations for Plain Text Authentication Configurations for MD5 Authentication Verify Verify Plain Text Authentication Verify MD5 Authentication Troubleshoot Troubleshoot Plain Text Authentication Troubleshoot MD5 Authentication Related Information Introduction This document shows sample configurations for Open Shortest Path First (OSPF) authentication which allows the flexibility to authenticate OSPF nei...

    pdf9p vanmanh1008 21-05-2013 20 2   Download

CHỦ ĐỀ BẠN MUỐN TÌM

Đồng bộ tài khoản