Link xem tivi trực tuyến nhanh nhất xem tivi trực tuyến nhanh nhất xem phim mới 2023 hay nhất xem phim chiếu rạp mới nhất phim chiếu rạp mới xem phim chiếu rạp xem phim lẻ hay 2022, 2023 xem phim lẻ hay xem phim hay nhất trang xem phim hay xem phim hay nhất phim mới hay xem phim mới link phim mới


Nghệ thuật xếp hình Nhật Bản:pot_with_leaves_and_stem_2

Chia sẻ: Phong Thinh | Ngày: | Loại File: PDF | Số trang:4

lượt xem
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình: pot_with_leaves_and_stem_2. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:

Nội dung Text: Nghệ thuật xếp hình Nhật Bản:pot_with_leaves_and_stem_2

  1. Pot with Leaves and Stem by Kalei Anne Lundberg copyright 2001 This model was designed to make use of variegated paper. If you want to experiment with your own paper design, either affix a square the color you would like the pot to be (using acid-free glue stick) or dye the paper, following the coloring design. The diagrams are offered for personal use; for any other use please contact me for permission at 450 Coloring design. 1. Collapse into a colored preliminary fold. Turn model so free points are on the bottom. 1500 3. Valley fold top flap 2. Squash fold. Repeat to the right. Repeat on on the back side. the back side. 5. Petal fold. Repeat on the back side. 4. Squash fold. Repeat on back side. Flower Pot page 1 of 4
  2. 6. Valley fold the 7. Valley fold the top two 8. Repeat steps 5 9. (Lilly/Frog base) small point left hand flaps to the right and 6. Fold and unfold to downward. Repeat and the back two right mark then open on the back side. hand flaps to the left. sink the top point. (Minor Miracle) 10. Inside reverse 11. Valley fold 12. Valley fold 13. Repeat step 10. fold the small point one flap to the another flap to the to the inside of the right. right. model. 1800 14. There should be 3 free points on the 15. Valley fold bottom right and one 16. Valley fold one 17. Rotate model so flap upward. on the bottom left. layer to the right. the sink is at the Turn model Valley fold one layer bottom. over. to the left. Flower Pot page 2 of 4
  3. Notes: I found that the easiest way to perform steps 18-22 was to do both sides at the same time. Because the hidden paper movement is beyond my diagramming capabilities, the following instructs you to fold one side at a time. This works, but is not the quickest method. Basically, what needs to be done is to return the face of the lily base (that will become the stem in the model) back to a bird base form by pulling out the paper and spread squashing the sink folds of the lily/frog base. The inside reverse fold in step 21 needs to be slipped behind the resulting triangular shaped sink fold (dotted line in step 21) so as not to be trapped by the valley folds in step 23. 18. Valley fold 19. Pull out 20. Open flap and 21. Inside reverse. Note one layer to the paper. mountain fold along the the corner of this fold left. center line. Pull to the should be tucked behind right. This will spread the interior triangular flap squash the interior folds. created in step 20. 22. Repeat steps 18- 23. Valley folds. 24. Valley fold top left 25. Valley fold 21 on the other side. layer to the right and downward. Repeat two back right layers on back side. to the left. Flower Pot page 3 of 4
  4. 28. Rabbit ear. 29. Squash fold. 26. Valley fold to narrow 27. Valley fold the the stem. Repeat on back three leaf flaps side. Note this fold extends upward. into the pocket. 30. Repeat steps 28 & 31. This step will make the model 3D. Mountain fold the leaf 29 on the other two flaps to the inside of the model. Care should be taken to loosen leaves. the central sink just enough to slide the leaves inside as the tension of the sink is used to hold the form of the pot. The two leaf flaps that are adjacent to the stem should be folded over the interior flap inside the model to lock the back corners of the pot and the leaf flap opposite the stem just folds to the inside. Several different leaf shapes can be formed STEM from the squash fold in step 29 to suit the type of flower or the squashes can be narrowed to make extra smaller stems. The stem can be rabbit eared or double rabbit If necessary the eared to give it a rounder shape. stem corner can Shape the leaves 6” paper will make a model about 1” wide at be locked from by curling, add a the base and 3” tall. the bottom. flower and you are done. Flower Pot page 4 of 4



Đồng bộ tài khoản