Link xem tivi trực tuyến nhanh nhất xem tivi trực tuyến nhanh nhất xem phim mới 2023 hay nhất xem phim chiếu rạp mới nhất phim chiếu rạp mới xem phim chiếu rạp xem phim lẻ hay 2022, 2023 xem phim lẻ hay xem phim hay nhất trang xem phim hay xem phim hay nhất phim mới hay xem phim mới link phim mới


Nghệ thuật xếp hình Nhật Bản:squirrel_2

Chia sẻ: Minh Tuan | Ngày: | Loại File: PDF | Số trang:6

lượt xem
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình:squirrel_2. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:

Nội dung Text: Nghệ thuật xếp hình Nhật Bản:squirrel_2

  1. Squirrel By Perry Bailey c 1998 1 2 Make a fish base as shown in diagram 3. 3 Valley fold over the flap on each side in line with the crease from the previous folds. 4 Open out the model, without bending the two flaps. 5 Valley fold the edges to the center, then fold the model back together.
  2. 7 6 Reverse fold the front of the model upwards. From figure 7 until we finish the front of the model we are going to show only the front of the model. 8 9 Enlarged view. Crimp Fold the flap Down. Crimp fold down even with the interior edges. 11 Open up the inside of the head, with the thumb or finger 10 of your choice, push the inner layer back, while bringing the head down. Sort of a crimp, while unsinking type of fold. Reverse fold head upwards..
  3. 13 Head should resemble this, hopefully! 12 The head has been enlarged yet again to make this easier for me to diagram, though it just might help the folder too. 14 15 To finish the ears valley Crimp the back of the head fold over a little of the back downwards to make the ears. of the head and then round out the ears. This finishes the head. 17 16 The big flaps we made earlier are the back legs. Valley fold up and then mountain fold back down to make feet. Then to create the illusion of haunches mountain fold over part of the hind leg behind it’s self. The next two diagrams 18 and 19 show the back of the leg so you can see what really takes place.
  4. 20 18 19 This is the lock used inside the The main body should look hind leg and feet. like this. 22 21 Reverse fold the tail upwards. 23 Open up the tail at the back of the model. Now we begin to work in 3 dimensions and I am sorry, but the diagramming is about to start suffering.
  5. 24 25 See, I told you I don’t do 3 dimensions well!! Now you open out the front Turn the model around so sort of like you did the back. you are looking at it from the front, it would look sort of like 25 if you made the body and head disappear 26 27 Note the paper sort of buckles, at one point don’t worry when you fold the tail down as shown in 27 it will take care of it. Mountain fold the back in at the base. Then valley fold the entire tail downwards. Then two crimp folds to finish it with.
  6. 28 The best I could draw the finished model. So I included the scanner Photo below.



Đồng bộ tài khoản