Link xem tivi trực tuyến nhanh nhất xem tivi trực tuyến nhanh nhất xem phim mới 2023 hay nhất xem phim chiếu rạp mới nhất phim chiếu rạp mới xem phim chiếu rạp xem phim lẻ hay 2022, 2023 xem phim lẻ hay xem phim hay nhất trang xem phim hay xem phim hay nhất phim mới hay xem phim mới link phim mới


Nghệ thuật xếp hình Nhật Bản:vase_lundberg

Chia sẻ: Phong Thinh | Ngày: | Loại File: PDF | Số trang:5

lượt xem
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình: vase_lundberg. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:

Nội dung Text: Nghệ thuật xếp hình Nhật Bản:vase_lundberg

  1. Weighted Vase by Kalei Anne Lundberg copyright 2001 This model was heavily inspired by a discussion on the Origami List and the Rose by Toshikazu Kawasaki from Origami for the Connoisseur. A 10” square will make a vase about 4” tall. Fender washers or coins are used for the weight. The diagrams are offered for personal use; for any other use please contact me for permission at 1. Valley fold and unfold. 2. Book fold and unfold. Turn paper over. 3. Line up the two mountain fold and crease between. 4. Repeat step 3 for the other flap. Weighted Vase page 1 of 5
  2. 5. Open paper upwards to preserve the center pleat. 6. Inside reverse fold the bottom left and top right corner of the pleat. Valley fold the other two corners. 900 7. Unfold all and turn paper 8. Repeat steps 1-7 to complete the basic grid. Note: I 90 degrees. will color the inside reverse folds from step 6 to identify their placement so they may be used as a landmark for the twist. Weighted Vase page 2 of 5
  3. 9. Mountain fold and unfold the two 10. Collapse into a colored waterbomb diagonals. fold. 11. Valley fold and unfold the tip to the first crease line. Open up the paper. 12. Pinch the four sides of the center square into mountain folds. Then preserving the mountain folds that rise from the corners valley fold just the center square in half along one of its diagonals. (A half sink) Weighted Vase page 3 of 5
  4. 13. Once the half sink is collapsed there will be extra paper on the front and the back. Valley fold this paper to align along the edge of the inside reverse from step 6 on both sides and flatten. 14. While opening up the paper, valley fold the top two edges to align with their respective inside reverses, and flatten. 15. Completed twist. Turn paper over. 16. Insert a coin or a metal fender washer or two into the twisted pocket to weight the vase. The diameter of the weight should be just a bit less than the length of one side of the twisted pocket. Form the box corners by valley folding along existing creases. The mountain fold indicated by the white circle will be a new crease and complete the accordion Weighted Vase page 4 of 5 pleat in the corner.
  5. 17. Step 16 in progress. Note that 18. Make the corners on 19. Valley fold the top left the accordion pleat radiating from the other 3 sides. Note: corner along existing the corner will align with the center This diagram shows only crease and reform the line of the inside reverse. one face as the model is inside reverse. now 3D. 20. Valley fold the top over and 21. Holding the four points together 22. Fold the top insert into the pocket formed by push along the center creases of layer to the right the valley fold. Repeat for each the four sides until they meet in on all four sides. corner. Note: If necessary a the center to form a channel to hold paper clip can be used to hold the stems. This will elongate the the lock in place until after the model and partially untwist the elongation. bottom pocket. 23. Finish the elongation by 24. Valley fold the top point 25. Pinch the center opening pinching a mountain fold down through all layers at the together...all done. If more though both layers from the indicated angle on each side. weight is needed, the bottom of the folded over This just helps to keep the flap pyramidal void in the bottom flap to the corner on the left in the open position. of the vase can be filled with for each of the four sides. small ball bearings or BBs. Weighted Vase page 5 of 5



Đồng bộ tài khoản