Hướng dẫn thiết kế Iphone 4S bằng Solidworks

Chia sẻ: Đặng Thanh Nhựt | Ngày: | Loại File: PDF | Số trang:18

Thêm vào BST

Báo xấu

80
lượt xem 17
download

Download Vui lòng tải xuống để xem tài liệu đầy đủ

Tài liệu Hướng dẫn thiết kế Iphone 4S bằng Solidworks giúp các bạn biết được quy trình của việc thiết kế Iphone 4S bằng phần mềm Solidworks. Với những hình ảnh minh họa trực quan sinh động và theo từng bước cụ thể sẽ giúp các bạn nắm bắt quy trình này được tốt hơn.

Chủ đề:

Bình luận(0) Đăng nhập để gửi bình luận!

Lưu

Nội dung Text: Hướng dẫn thiết kế Iphone 4S bằng Solidworks

Sudhir Gill 2015 5. Step 5 Tutorial - Making iPhone 4s Extrude it as thin feature of .6 and mid plane by 6.17mm. in SolidWorks Part 1-4 1. Step 1 Start SolidWorks. 6. Step 6 Chamfer the edges by 0.25 at 45º. 2. Step 2 Front Plane >> Sketch. 7. Step 7 Right plane >> Sketch. 3. Step 3 Draw this. 8. Step 8 Draw a rectangle. 4. Step 4 Fillet corners. DANG THANH NHUT Page 1
Sudhir Gill 2015 9. Step 9 Draw on the upside also. 14. Step 14 Select sketch of Extrude1 and click Convert entities. 10. Step 10 Curves >> Split line. 15. Step 15 Extrude it by 9.34mm. 11. Step 11 Select all faces. And click OK. 16. Step 16 Fillet the edges by 0.25mm. 12. Step 12 Now the split faces have been generated. 13. Step 13 Front plane >> sketch. DANG THANH NHUT Page 2
Sudhir Gill 2015 17. Step 17 Front face >> Sketch. 22. Step 22 Select the split face and dome it by 0.50mm inwards. 18. Step 18 Draw circle at vertical to origin. 23. Step 23 Front face >> Sketch. 19. Step 19 Curves >> Split line. 24. Step 24 Draw a rectangle at the center of circular face. 20. Step 20 Select the front face and click OK. 25. Step 25 Fillet it's edges by 0.65mm and then offset it by 0.40mm 21. Step 21 Select dome tool. DANG THANH NHUT Page 3
Sudhir Gill 2015 26. Step 26 30. Step 30 Split line and select the domed surface. Click OK. Chamfer the edge by 0.775 and 0.80mm. 27. Step 27 31. Step 31 Front face >> Sketch. 1. Step 1 Front face >> Sketch. 28. Step 28 Draw a slot. 2. Step 2 Draw a circle of 4.8mm dia. 29. Step 29 Extrude cut by 1mm. 3. Step 3 Extrude cut by 1mm at draft of 50º. DANG THANH NHUT Page 4
Sudhir Gill 2015 4. Step 4 8. Step 8 Front face >> Sketch. Draw a circle of 2mm dia. 5. Step 5 9. Step 9 Convert the edge. Split line and select the inner face. 6. Step 6 10. Step 10 Extrude it by 0.25 at 50º draft. Hide the extrusion body. 7. Step 7 11. Step 11 Front face >> Sketch. Hide the previous extrusion. Dome the inner surface by 0.40mm. DANG THANH NHUT Page 5
Sudhir Gill 2015 12. Step 12 16. Step 16 Top face >> Sketch. Offset the edge by 0.25mm. 13. Step 13 17. Step 17 Draw a slot. Extrude it by 1.10mm without merging result. 14. Step 14 18. Step 18 Extrude cut it by 0.50mm. Chamfer the edge by 0.20mm at 45º. 15. Step 15 19. Step 19 Inner face >> Sketch. Left face >> Sketch. DANG THANH NHUT Page 6
Sudhir Gill 2015 20. Step 20 24. Step 24 Draw a rectangle and fillet its's corners. Inner face >> Sketch. 8 21. Step 21 25. Step 25 Draw another circle. Draw a slot. 22. Step 22 26. Step 26 Draw 2nd circle. Draw two circles. 23. Step 23 27. Step 27 Extrude cut them by 0.50mm. Extrude them by 1.10mm. DANG THANH NHUT Page 7
Sudhir Gill 2015 28. Step 28 32. Step 32 Chamfer the edge by 0.2mm at 45º. Extrude cut by 0.2mm. 29. Step 29 1. Step 1 Circular face >> Sketch. Top face >> Sketch. 30. Step 30 2. Step 2 Draw this sketch. Draw two circles. 31. Step 31 3. Step 3 On lower circle draw this sketch using slot. Extrude cut by 15mm. DANG THANH NHUT Page 8
Sudhir Gill 2015 4. Step 4 8. Step 8 Chamfer the edges by 0.275mm at 45º. Back face >> Sketch. 5. Step 5 9. Step 9 Top face >> Sketch. Draw a circle and offset it. 6. Step 6 10. Step 10 Offset the circular edge by 0.13mm and 0.26mm. Split line and select the back face. Click OK. 7. Step 7 11. Step 11 Split line and select the face. Click OK. Select the previous sketch and then Extruded cut. DANG THANH NHUT Page 9
Sudhir Gill 2015 12. Step 12 16. Step 16 Extrude cut by 0.25mm with inner contour. Inner face >> Sketch. 13. Step 13 17. Step 17 Inner surface >> Sketch. Draw a circle. 14. Step 14 18. Step 18 Draw a circle. Extrude cut by 0.50mm. 15. Step 15 19. Step 19 Extrude cut by 1mm. Inner face Sketch. DANG THANH NHUT Page 10
Sudhir Gill 2015 20. Step 20 24. Step 24 Offset the inner edge by 0.250mm. Select this edge and Convert entities. 21. Step 21 25. Step 25 Split line and select the inner face. Click OK. Extrude it up to this surface. Uncheck Merge result. 22. Step 22 26. Step 26 Dome the internal surface by 0.5mm. Back face >> Sketch. 23. Step 23 27. Step 27 Select this face >> Sketch. Draw two concentric circles. DANG THANH NHUT Page 11
Sudhir Gill 2015 28. Step 28 5. Step 5 1. Step 1 Circular face >> Sketch. Split line and project them on back face. 6. Step 6 2. Step 2 Convert the edge. Inner face >> Sketch. 7. Step 7 3. Step 3 Extrude it by .10mm and uncheck Merge result. Convert the inner edge and extrude cut it by 0.50mm. 8. Step 8 4. Step 4 Bottom face >> Sketch. Dome it by 0.4mm. DANG THANH NHUT Page 12
Sudhir Gill 2015 9. Step 9 13. Step 13 Draw a slot. Draw this slot. 10. Step 10 14. Step 14 Mirror it about a center line on origin. Split line and then select inner face. 11. Step 11 15. Step 15 Extrude cut by 1mm. Bottom face >> Sketch. 12. Step 12 16. Step 16 Left face >> Sketch. Draw a rectangle. DANG THANH NHUT Page 13
Sudhir Gill 2015 17. Step 17 21. Step 21 Extrude cut by 2.5mm. Split line and select bottom face. 18. Step 18 22. Step 22 Chamfer the cut edge by 0.15mm at 45º. Circular face >> Sketch. 19. Step 19 23. Step 23 Bottom face >> Sketch. Draw a 5 side polygon and construct star. 20. Step 20 24. Step 24 Draw two circles. Repeat same step for other circular face. Make polygon construction. DANG THANH NHUT Page 14
Sudhir Gill 2015 25. Step 25 4. Step 4 Extrude cut by 0.50mm. Front face >> Sketch. 26. Step 26 5. Step 5 Here is the fifth part. Change vision to hidden line visible. Convert the edge and convert it 1. Step 1 to construction. Draw a rectangle taking it reference. Inner face >> Sketch. 6. Step 6 2. Step 2 Linear pattern it at a distance of 0.5mm 30 times. Draw a rectangle. 7. Step 7 3. Step 3 We have the pins. Extrude it by 1.50mm. DANG THANH NHUT Page 15
Sudhir Gill 2015 8. Step 8 12. Step 12 Split Line and select this face. Click OK. Split line and project it on right face. 9. Step 9 13. Step 13 Now the pins are generated. The slot face >> Sketch. 10. Step 10 14. Step 14 Right face >> Sketch. Draw a circle. 11. Step 11 15. Step 15 Draw a slot. Extrude cut by 1.8mm. DANG THANH NHUT Page 16
Sudhir Gill 2015 16. Step 16 20. Step 20 Front face >> Sketch. Project it on Front face. 17. Step 17 21. Step 21 Draw a rectangle. Back face >> Sketch. 18. Step 18 22. Step 22 Fillet the edges. Use spline tool and make this sketch. 19. Step 19 23. Step 23 Curve >> Split line. Project it on the back face. DANG THANH NHUT Page 17
Sudhir Gill 2015 24. Step 24 We have iPhone 4s in SolidWorks. 25. Step 25 Whow the boss-extrude. 26. Step 26 Now apply different appearance to different faces and iPhone 4s is ready. DANG THANH NHUT Page 18