Hướng dẫn cách gấp giấy - 4

Chia sẻ: Long Long | Ngày: | Loại File: PDF | Số trang:7

Thêm vào BST

Báo xấu

763
lượt xem 119
download

Download Vui lòng tải xuống để xem tài liệu đầy đủ

Tài liệu hướng dẫn bạn cách gấp giấy hình con bọ ngựa (Tài liệu bằng tiếng Anh)

Chủ đề:

Bình luận(0) Đăng nhập để gửi bình luận!

Lưu

Nội dung Text: Hướng dẫn cách gấp giấy - 4

Praying Mantis by Robert J. Lang Copyright ©1990. All rights reserved. 1. Crease the diagonals. 2. Fold and unfold. 3. First make the horizontal crease halfway between the two pinch marks. Then make the vertical crease through the intersection of the horizontal crease and the diagonal of the square. 4. Fold the corners in and turn 5. Fold a Waterbomb Base 6. Swivel-fold. the paper over. based on the new creases. PostScript routines that were coded by the author. The design and These drawings were composed on a Macintosh SE computer using the program Aldus FreeHand 2.0, linked with additional these drawings may not be distributed commercially. 7. Fold and unfold. 8. Open-sink the corner..
9. Open out the sink and push some paper up 10. Reverse-fold 11. Pull down the edge of the from the inside; pinch the excess paper in half the corner. pocket and fold the right layer and swing it over to the left. back to the left. 12. Fold one flap down. 13. Swing one layer from right to left. 14. Repeat steps 6–13 on the right. 15. Squash-fold. 16. Petal-fold. 17. Unwrap a single layer. 18. Squash-fold. 19. Reverse-fold the edges. 20. Turn the model over. 21. Repeat steps 15–17.
22. Fold and 23. Fold the flap down, using the 24. Reverse-fold a single 25. Reverse-fold unfold. newly-made creases as a guide. layer out from the inside. the edges. 26. Reverse- 27. Pull out the layers 28. Open-sink 29. Flatten 30. Fold and 31. Fold one fold the trapped under the the shaded the sunk unfold. layer to the left bottom triangular hood. The region and region. in front and corner. model will not lie flat. refold. one to the right behind. 32. Top of the model. 33. Pleat and fold a rabbit 34. Fold and unfold 35. Wrap one layer of Fold and unfold. ear from the thick point through all layers. paper to the front. using the existing creases. 36. Fold one layer to 37. In progress. 38. Close the 39. Repeat steps 40. Swing the point the right, releasing Pull paper out model back up. 36–38 on the next over to the left. the trapped paper at from here. two layers. the left that links it to the next layer.
41. Repeat steps 42. There are four edges on 43. Pull out the 44. Swing the point 36–39 on the right. the top right; pull out as much loose paper back to the right. of the loose paper between the between the first third and fourth edges as and second possible. A hidden pleat layer. disappears in the process. 45. Repeat steps 46. Fold and unfold. 47. Open-sink the 48. Rearrange the 42–43 on the left. point. You will have layers at the top so that to open out the top of the central square forms the model somewhat a Preliminary Fold. to accomplish this. 49. Fold one layer to the right in front, and one to 50. Petal-fold. 51. Fold the flap 52. Closed-sink the the left behind. The back upward. point. (Be careful! model should be It is very easy to symmetric as in step 31. rip the paper.) 53. Repeat 54. Reverse-fold the 55. Fold two layers to 56. Crease 57. Sink (open at the steps 50–52 long edge all the way the right (in the into thirds. bottom, closed at the behind. through the model process, you undo the top) the edge in and (closed-sink the reverse fold you made out on the existing corner at the top). back in step 11). creases.
58. Sink the 59. Fold one 60. Fold 61. Crimp the top left 62. Mountain- 63. Fold one corner at the layer back to one layer in corner. Fold one layer fold the edge layer from top. the left. thirds. from the right to overlap underneath. right to left. the left layer, flattening the point behind. 64. Repeat 65. Turn 66. Fold one 67. Fold and 68. Pleat steps 55–62 the model flap up. unfold; the crease above the on the right. over. lies on top of the crease you horizontal edge of just made. the layers behind. 69. Crease 70. Fold the flap 71. Fold the 72. Mountain- 73. Repeat 74. Fold the into thirds. over on one of the next layer over fold both layers steps 69–72 top point creases you just the top of the together. on the right. down to the made, and make a one you just right. linked pair of swivel folded. folds at the top.
75. Unfold. 76. Fold the top 77. Pull out 78. Squash-fold 79. Pull out 80. Reverse-fold down to the left. some loose the flap over to some loose the point. paper. the right. paper. 81. Squash-fold. 82. Petal-fold. 83. Bring one 84. Fold the two 85. Narrow the layer to the front points upward two points and on each side. (the exact the sides of the amount isn't main flap. critical). 86. Fold the 87. Double-rabbit-ear 88. Repeat on 89. Fold up one point 90. Fold each head down. the left point. the right. as far as possible on side in thirds. each side.
91. Open-sink the 92. Reverse-fold the 93. Reverse-fold the 94. Narrow the legs side corners (top point out to the side. next point out to the with mountain and layer only). side. valley folds. 95. Swing the white 96. Repeat steps 97. Turn the model over. layer over to the 92–95 on the left. right. 99. Shape the legs by pinching 100. Praying Mantis them in half. Pinch and 98. Fold the lower portion of the reverse-fold the forelegs to model in half, but keep the shape them. Mountain-fold the upper portion flat. Fold the edges of the body. Reverse-fold forelegs down away from the the white edge at the abdomen body. upward.