Link xem tivi trực tuyến nhanh nhất xem tivi trực tuyến nhanh nhất xem phim mới 2023 hay nhất xem phim chiếu rạp mới nhất phim chiếu rạp mới xem phim chiếu rạp xem phim lẻ hay 2022, 2023 xem phim lẻ hay xem phim hay nhất trang xem phim hay xem phim hay nhất phim mới hay xem phim mới link phim mới


Nghệ thuật xếp hình:b-wing

Chia sẻ: Phong Thinh | Ngày: | Loại File: PDF | Số trang:6

lượt xem
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình: b-wing tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:

Nội dung Text: Nghệ thuật xếp hình:b-wing

  1. B-Wing Starfighter © James B. Raasch III, 12/14/97 1) 2) 3) Begin with a bird base, colored side out, and Fold the triangular peak all the way down. Fold tip ‘A’ to tip ‘B’. Unfold. fold the front flap all the way up. Turn the model over. Note that no shading is shown because there are no color changes, and it makes some of the folds easier to see. 4) 5) 6) Fold crease ‘A’ to crease ‘B’. Fold the top flap up along the existing Fold the triangular peak all the way up. crease. This will become the cockpit. Page 1 of 6
  2. B-Wing Starfighter © James B. Raasch III, 12/14/97 7) 8) 9) Fold the bottom flap all the way up. This will Fold the wing flap down, about half way Squash the sides of the wing flap so that the become the main wing between the crease you just made and the edges are vertical. Again, the exact amount edge formed from creasing the top flap. is not important, but try to line up the The exact amount is not important. intersection of the top of the horizontal creases and the cockpit flap with the vertical crease. The intersection is hidden in the diagram. 10) 11) 12) Fold the triangular peak down at the crease Fold the model in half along the vertical axis Squash-fold the top flap up and to the left. you made in step 8. from right to left. Repeat on the flap on the back. These will Page 2 of 6
  3. B-Wing Starfighter © James B. Raasch III, 12/14/97 13) 14) 15) Petal fold the s-foil right. Repeat behind. 0 Unfold the fold on the left side that was Fold the flap up and to the left along a 45 line. Repeat behind. made when you made the petal-fold in step 13. Repeat behind. 16) 17) 18) Fold the front half of the s-foil back along Fold the flap up along the horizontal. Fold the s-foil down as far as you can. This the centerline, and tuck it under the top Repeat behind. crease will be horizontal, and will fall along sheet of paper. Repeat behind. the edge of the engine pod. Repeat behind. Page 3 of 6
  4. B-Wing Starfighter © James B. Raasch III, 12/14/97 19) 20) 21) Inside-reverse fold the tip of the s-foil to Outside-reverse fold the end of the main Finish forming the main wing by folding this make the wingtip cannon. If you treat the wing to make the main wing cannon. flap inside the body. The midpoint of the flap you folded inside in step 17 as one side, 450 line made by the outside-reverse fold and do the reverse between that flap and makes the bottom endpoint of the crease. the single sheet, you will end up with the The exact position, however, is not bottom of the cannon white. Repeat behind. important, as long as it looks good. Repeat behind. 22) 23) 24) Fold the tip of the cockpit flap down to the Squash the flap up and to the left. Fold the flap over as far as you can to the bottom horizontal crease. right. Page 4 of 6
  5. B-Wing Starfighter © James B. Raasch III, 12/14/97 25) 26) 27) Fold the lower half of the flap up. Fold the tip down to the crease that formed Fold the tip to the vertical edge and unfold. in the last step. Repeat behind. 28) 29) 30) Fold the flap down along the crease made in Fold the tip of the nose in along the crease Fold the back of the engine pod into the step 26. Repeat behind. made in step 28. body. Repeat behind. Page 5 of 6
  6. B-Wing Starfighter © James B. Raasch III, 12/14/97 31) Fold the s-foils up to a horizontal position, and your B-Wing is ready to fly. The completed B-Wing. This is a pretty crude isometric view, but hey, I don't do this for a living. There are two things I am unhappy with; the S- Foils should be below the engine pod, and the model is so thick that it needs a locking mechanism. Maybe those items will get fixed in a future revision (i.e., when I have more time). Page 6 of 6



Đồng bộ tài khoản