Nghệ thuật xếp hình Nhật Bản: puppy pounce

Chia sẻ: Nhut Thinh | Ngày: | Loại File: PDF | Số trang:5

Thêm vào BST

Báo xấu

155
lượt xem 19
download

Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình Nhật bản: puppy pounce. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:

Bình luận(0) Đăng nhập để gửi bình luận!

Lưu

Nội dung Text: Nghệ thuật xếp hình Nhật Bản: puppy pounce

Puppy Pounce By Perry Bailey c 1997 1 2 Valley fold and unfolding the diagonal both ways. Paper white side up. Valley fold the sides to the center. 3 4 Valley fold the top flap down even with the raw edges of the previously folded flaps. Pull out the two side flaps.
5 6 Valley fold the sides from the Reach under to the top to the center of the model. hidden center flap and pull it out. 7 8 Squash fold the flap down as if making a preliminary base. Petal fold the top flap up as if for the bird base. 9 10 1/2 1/2 1/2 1/2 Valley fold the top layer only at the angle bisector, then fold over the flap as shown to form an irregular rabbits ear. Note, Mark the spot half way between the long line on the bottom the corner of the bird base and layer does not go to the tip. the crease formed in step 2. It is formed by flattening the paper after the two folds on the top layer.
11 Valley fold the flap back 12 across it’s self, so that the angle bisector you folded in the last step is unfolded in this step. Swivel fold the flap under itself so the raw edge and the crease meet, on the upper part. The crease will not meet the edge all along the lower part. Repeat steps 10 - 13 14 on other side. Fold the flap up in a rabbits ear fold. Note that when folded up the paper under the flap that comes to the surface 15 will be fully extended. 13 Valley fold in half and turn 90 degrees to the left. Paper thickens 16 here 1/2 1/2 17 Crimp fold the front of the model back so that the bottom of the crimp is even with Now we form the head, all it takes in order where the paper thickens at the top, and so left to right, a crimp, a pleat an outside reverse that it will stick up above the surface at the fold. top
19 18 This is a cut away view of the inside of Valley fold the legs forward, as seen in 19 the model, is if the entire front half where Pull the snout down a little to taste. missing. At this point work a colour change on the front legs by taking the bottom layer of the front leg and pull it out. 20 21 Then tuck the layer you pulled out in the previous step and tuck it into the leg, this will make the leg the same colour as the body. Reverse fold the tips of the front legs in to themselves. Then reverse fold the top two layers of the rear end over towards the front. 22 23 Reverse fold the hind end down. Reverse fold the tail up. 24 25 Fold the tail down with a crimp fold, then Crimp fold the tuck the outside flaps in to the model. body to form the rear end of the dog. (Here is a hint, do it one side at a time.)
25 Mountain fold the excess paper up inside of the model and your done! 26 To See the puppy pounce, just tap his tail!