intTypePromotion=1
zunia.vn Tuyển sinh 2024 dành cho Gen-Z zunia.vn zunia.vn
ADSENSE

Nghệ thuật xếp hình Nhật Bản: RHINO

Chia sẻ: Nhut Thinh | Ngày: | Loại File: PDF | Số trang:6

186
lượt xem
38
download
 
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình Nhật bản: RHINO. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:
Lưu

Nội dung Text: Nghệ thuật xếp hình Nhật Bản: RHINO

  1. Black Rhinoceros c Ronald Koh - 1993 1. 2. A sheet of paper of at least 20 cm square Now fold the lower diagonal edges to meet would be preferred for this model. Fold and along the vertical crease line in the centre. unfold diagonally in half, creasing well. 3. 4. 5. Turn paper over ... ... and fold down the Turn the paper over triangular portion at the again ... top as illustrated. 6. 7. ... and unfold the overlapping layer to ... like this. Now fold vertically in half, each side ... from left to right ...
  2. 8. 9. 10. ... then valley fold along the Separate the two layers Fold and unfold, edge of the white triangular along the horizontal edge Creasing firmly ... portion, crease firmly, and and squash fold. unfold. 11. 12. 13. Do a petal fold by pulling the ... like this. Turn the ... separate the two layers diagonal edge of the paper over, ... along the diagonal uppermost layer 45 degrees edges on the left and down and to the left, while squash fold. drawing in the horizontal and 15. vertical edges at the top 16. together ... 14. Valley fold the horizontal edge ... then fold done the Fold down both corners at of the white layer to meet the coloured triangular the top, and do a rabbit's diagonal edge of the coloured portion in the middle ear fold at the bottom ... layer on each side, ... as illustrated. 17. 18. ... like this. Separate the two layers of the triangular tab and squash fold, ... ... then mountain fold along the existing diagonal crease lines to narrow the upper section before bringing the point at the top to meet the point at the bottom ...
  3. 19. 20. 21. ... like this. Fold the lower diagonal edges to Fold and unfold again as meet the adjacent diagonal edge illustrated, creasing firmly again. of the kite-shaped flap in the centre, crease firmly, and unfold. 22. 23. 24. Fold the first layer up,... ... then turn the model over. 25. Grasp each side at the circled areas, holding the coloured portions only, then pull apart to open out ... 26. ... like this. Now lift up the the white triangular layer at the top and the second layer at the bottom ... 27. ... then collapse along the existing crease lines with mountain and valley folds as illustrated ... ... like this ...
  4. 28. 29. 30. Valley fold the triangular tabs in the middle upwards, at the same time valley folding the Draw one layer to the left and ... as illustrated, then fold and lower diagonal edges to squash fold ... unfold, creasing firmly. meet in the centre ... 32. 33. 31. ... like this. Fold down the triangular tabs in the middle again. Swivel one layer on the Fold and unfold, creasing right to the left. firmly, ... 34. 35. ... then reverse fold along the ... like so. Fold and unfold, creasing crease lines made in Step 33 firmly again, ... ... 36. 37. ... then mountain fold the excess Rabbit's ear fold as shown, paper under along the crease line swivelling one layer on the left made in Step 35. to the right.
  5. 38. 39. 40. Swivel one layer on Turn model Separate the two the left to the right, and over. layers along the repeat from Step 33 on diagonal edges this side. and squash fold, ... 41. 42. 43. 44. ... then narrow as illustrated ... 45. ... like this. Reverse fold the Fold the flap ... and crimp with a corners along the down again ... mountain and existing crease lines and valley fold, ... bring the resulting point at the bottom all the way to the top. ... like this. 46. 47. 48. 49. Fold down one layer ... then fold up Turn the model from the top ... again, making a over. little crimp. 50. Fold down the first layer at the apex of 51. the model and crease well, then reverse fold the points on each side. Fold up the the first layer at the apex again, and valley fold the lower points Valley fold the lower upwards at the illustrated points down again. angles and proportions.
  6. 52. 53 54. 55. Unfold the Steps ... and refold along ... like this. at 49 and 50 on the crease lines the apex of the as illustrated, ... 56. model ... 57. Make a crimp as illustrated with a mountain and valley fold, ... ... then mountain fold the model vertically in half. Grasp the head firmly and pull down gently ... 59. 60. 58. Rabbit's ear fold the triangular Outside reverse fold the tabs on each side to form the next point to form the ears, then flatten the head second horn, and valley temporarily and outside fold the little corner on reverse fold the short point in each side to form the eyes. the middle to form one horn. Broaden each hind leg by drawing out the second layer 61. to the back as indicated by 62. the dotted lines. 63. Sink the front section of the horn. A pair of 64. Crimp fold the front tweezers will help. of the remaining Open out both ears as ... then lift up the point under ... shown. first layer on each side ... ... like this. 65. 66. Inside reverse fold all the legs and the Narrow both sides of the forelegs base of the tail as illustrated. by fold the excess paper within. Do another reverser fold at the tip of the tail, then complete the model by rounding off the back.
ADSENSE

CÓ THỂ BẠN MUỐN DOWNLOAD

 

Đồng bộ tài khoản
2=>2