Link xem tivi trực tuyến nhanh nhất xem tivi trực tuyến nhanh nhất xem phim mới 2023 hay nhất xem phim chiếu rạp mới nhất phim chiếu rạp mới xem phim chiếu rạp xem phim lẻ hay 2022, 2023 xem phim lẻ hay xem phim hay nhất trang xem phim hay xem phim hay nhất phim mới hay xem phim mới link phim mới


Nghệ thuật xếp hình Nhật Bản:shamrock_2

Chia sẻ: Minh Tuan | Ngày: | Loại File: PDF | Số trang:5

lượt xem
  Download Vui lòng tải xuống để xem tài liệu đầy đủ

Nghệ thuật xếp hình:shamrock_2. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.

Chủ đề:

Nội dung Text: Nghệ thuật xếp hình Nhật Bản:shamrock_2

  1. $ Shamrock Copyright 2000 Stephen Hecht. All Rights Reserved A dollar bill makes a model 70mm wide and 50mm tall. For first attempt, you may wish to use a larger 3x7 rectangle. pivot 2. Pivot at lower-left corner, 3. Repeat step 2 behind. 1. Start green side up. valley-fold lower right corner Unfold completely and Valley-fold in half. to top edge. turn over. 4. Valley-fold on existing 5. Bisect angle. crease. Crease only halfway up, then unfold. 6. Valley-fold raw edge to folded edge. 4-7 7. Pleat, bringing existing mountain-crease to folded 8. Repeat 4-7 in mirror 9. Valley-fold halfway and edge. Unfold completely. image. unfold.
  2. $ Shamrock (continued) Copyright 2000 Stephen Hecht. All Rights Reserved 10. Pleat on existing 12. Add valley-creases. creases. Order of layers The middle one and outside is not crucial. Turn over. 11. Mountain-fold on the pair are on existing crease existing crease, creasing lines. Squeeze in the other sharply. Unfold completely two last. Turn over. and turn over. 13. Triple-crimp. Start in the middle, work outwards. The new 14. Enlarged. Reverse- 15. Valley-fold to half-way valley-folds fall where natural; fold. Valley-line exists. crease and unfold. Flex the they don’t bisect angles. The Repeat behind. upper crease backwards. model will lie flat along the Repeat behind. existing radial creases. 16. Closed sink the upper 17. Closed-sink the next corner. Mountain-fold the corner, along the same line 18. Swing down. Note lower. Repeat behind. as the previous sink. Repeat new crease at the right. behind.
  3. $ Shamrock (continued) Copyright 2000 Stephen Hecht. All Rights Reserved 18-19 F E 19. Valley-fold edge “E” a little 20. Like so. Repeat 18-19 21. Difficult step: fold edge bit above the crease line. A behind. “F”down to leave a tiny gap flap comes out at bottom. between “leaves”. Do the same on the back version of “F”. Also spread lower flaps outwards. 1:push down 2: 23. Flatten completely and sharpen 22. View of back side. The small triangle is creases. From this point on, results may a 3-sided open-faced pyramid. Push down vary a bit due to judgement folds. Try to inside it to resolve tension on front side. Then keep left and right sides reasonably pinch it from the sides, and swing it down to similar. either side. Turn over, top-to-bottom. 1 4 D 3 5 B 1 2 A 24. Mountain-fold through all 26. Squash the standing layers, sharply only on the 25. An asymetric petal-fold. Fold in the order shown. flap. Start with the folds rearmost ply. Goes through the joining points “A” and “B” to bend in the middle “leaf”, at right Folds “1” exist. “Roll in” folds 2 and 5 with a fingertip. the “petal-peak”. See next angles to crease “D”. Turn over, diagram. top-to-bottom.
  4. $ Shamrock (continued) Copyright 2000 Stephen Hecht. All Rights Reserved 24-26 28 24-26 27. Approximate 29. Like so. Repeat last step positioning shown. Repeat 28. Repeat 24-26 (the on the left side. Left and right 24-26 on left side. Make asymetric petal-fold). side will probably diverge more; minor adjustments to keep try to keep them similar. If any model symetric. paper shows between leaves, swivel it upwards. 30. Tuck as much as possible 31. Reverse-fold, closed- 32. Squash-fold. Hidden inside (behind the petal folds), sinking at the thick corner. valley-fold makes top of leaf pleating if necessary. Judgement fold: check symetric. front side. 30-33 33. Stuff the flap into 34. Repeat 30-33 on 35. Thin the stem on both the pocket behind it, left side. sides. The crease bends, pleating if necessary. then becomes a spread- squash.
  5. $ Shamrock (continued) Copyright 2000 Stephen Hecht. All Rights Reserved 37. Middle leaf. Reverse- 38. Shape tip of leaf with a 36. Entire model not shown. fold, distributing layers “divot”. Repeat on left and Valley-fold stem into position. evenly. Repeat on left side right leaves. Turn over top-to-bottom. of leaf. 39. Trim with reverse-folds, as needed. 40. Finished Shamrock.



Đồng bộ tài khoản