ANSYS software

The paper "The behavior analysis of bolted end-plate connections under static load by using finite element method" investigates the mechanical behavior of bolted end-plate beam-to- column connections with changes of thin of end-plate and size of bolts under bending moment. The finite element models are generated in ANSYS software, in specially all of meshes are hexahedral meshes as well as be continuous at welding. The results obtained from this study are validated based on three factors: loading capacity, moment resistance and joint rotation.

9p dathienlang1012 03-05-2024 2 0   Download

This article researches to build a mathematical model of the axial stiffness coefficient and force generated by the geometric configuration of the crank pin-crank web assemblies and the combustion gas force. The numerical simulation is performed by finite element method, using ANSYS software, applied to the main engine MAN B&W 6G70ME.

6p vijaychest 24-04-2024 2 2   Download

Ebook The C programming language (Second edition) present the complete guide to ANSI standard C language programming. Written by the developers of C, this new version helps readers keep up with the finalized ANSI standard for C while showing how to take advantage of C's rich set of operators, economy of expression, improved control flow, and data structures. The 2/E has been completely rewritten with additional examples and problem sets to clarify the implementation of difficult language constructs.

288p longtimenosee05 31-03-2024 3 0   Download

DPF is an important device in the exhaust system of Diesel engine. In this paper we simulate velocity and pressure distributions in DPF to determine kinematic and hydraulic characteristics. This will provide the basis for designing and selecting size of channels in DPF. Numerical simulations were made using ANSYS Fluent commercial software and OpenFOAM open-source software.

11p vimarillynhewson 02-01-2024 2 1   Download

Research on the microchannel and its flow and heat transfer properties has received much attention. This study employed Autodesk Inventor software to build the model, and the Computational Fluid Dynamics software (Ansys Fluent 14) was used for numerical simulation. Taguchi analysis methods, ANOVA, and Minitab statistics testing were used.

11p vijeff 27-11-2023 8 6   Download

The main objective of this study is to perform a numerical investigation of flow inside a small cyclone separator. The steady state of the governing equations is solved by using Ansys Fluent 19.2 software.

10p vijeff 27-11-2023 8 4   Download

This paper aims to analyze effects of design parameters on the sensitivity of compliant micro-gripper. The micro-gripper is constructed based on a four-bar mechanism and a concept of compliant mechanism with circular hinges.

9p vidoctorstrange 06-05-2023 6 4   Download

This paper focuses on evaluating the formation and development of cavitation by time of reversible impeller of PaT when operating in pump mode by numerical simulation with ANSYS-Fluent software.

3p vilucius 15-03-2023 5 2   Download

Fluid – structure interaction (FSI) is the interaction of movable or deformable structure affected by fluid flow surrounding and takes an important role in many issues related to industry. This research focuses on investigation of sodium leakage incident issue at prototype fast breeder reactor Monju by using engineering simulation ANSYS software.

9p vicedric 08-02-2023 4 3   Download

This paper presents an experimental and numerical investigation on the static behavior of concrete beams reinforced with composite aramid bars. According, six beams of dimensions (100mm×150mm×1200mm) were cast and tested.

5p vimclaren 20-10-2022 5 3   Download

This paper presents an approximate method for analyzing the magnetic field to determine the location of the flow path in 3D. This method was verified on a hypothetical model built on ANSYS software and 3D physical model and then tested on magnetic field data measured at the study dam.

5p vimelindagates 18-07-2022 7 2   Download

This paper presents a numerical approach at the mesoscale for the mechanical behavior of TRC composite under tensile loading. A 2-D finite element model was constructed in ANSYS MECHANICAL software by using the codes. The experimental results on basalt TRC composite from the literature were used as input data in the numerical model.

9p vinikolatesla 31-03-2022 13 2   Download

Saving energy is quickly becoming an unavoidable issue for countries all over the world. One of the most important requirements for sustainable development is the efficient and economical use of energy. The electromechanical conversion stage consumes the most power of any stage of electricity use, accounting for more than 70 percent of total power consumption.

5p vishivnadar 17-01-2022 13 0   Download

In this paper, the skewing slot is applied to the PM surface mounted Brushless DC Motor 20kW 36 slots and 12 magnet poles (Z = 36, p = 12) for eliminating torque ripples. To observe the skewing stator effect, the stator lamination layers are skewed with different angles. With determined skewing angle, the cogging torque eliminated theoretically and flux density space harmonics are also reduced

4p viericschmid 12-01-2022 12 0   Download

The authors built a research model and a mathematical one by basing on the BEM method and simulating them by the Fluent-Ansys software. Then, results of simulated calculation of the current effect on controlling ship course in the Haiphong fairway are presented in order to improve the safety of navigation in this channel.

10p wangxinling 23-07-2021 14 0   Download

This report presents the results on the modeling and optimization the systems of two buoys for wave energy converter. The first is a floater. The second is a semi-submerged body. The energy is converted from the relative motion between the two buoys by the linear generator. For simulation in three dimensions, the system of equations (6 modes of motions) has been obtained. The governing equations are solved by ANSYS AQWA software and Matlab tools.

6p parasite 07-06-2021 17 2   Download

This paper presents an inverse method for finding quantity of heat sources in high speed spindle. A commercial ANSYS software and Conjugate Gradient optimization method are used to construct the proposed inverse method. Simulations for different number of measurementpoints andlocations are performed. These results show that excellent estimation on heat generation can be obtained through using only two measurement points. The current methodology will provide a useful tool to investigate the complex heat transfer process in the high speed spindle.

5p chauchaungayxua11 23-03-2021 13 1   Download

In this paper, the thermal model of butt joint in Gas Metal Arc Welding (GMAW) is constructed and simulated based on ANSYS software to obtain welding temperature field. Low carbon steel with temperature-dependent thermal properties due to very high welding temperature is considered. Volumetric heat source is determined through series equations for different welding conditions.

7p chauchaungayxua11 23-03-2021 12 1   Download

The gas tungsten arc welding (GTAW) process is widely used for welding T-joints of aluminum alloy plate. this paper presents an application of ansys software to simulate and predict T-joints’ temperature distribution, stress and distortion. The complication in determining the heat source of fusion welding processes is fully provided and considered in this study.

9p vinevada2711 19-03-2021 15 1   Download

The paper, finite elements analysis is performed using ANSYS Workbench software (version 18.2) on thin plates of bus with varying thickness and materials is of composite. The uniformly distributed and centralized load loading conditions are considered. The analysis result of deformation, stress and oscillation frequencies for different thicknesses. These results are compared analysis of the simulation accuracy.

4p caygaocaolon10 05-02-2021 17 2   Download