Numerical modelling

The selection of suitable material for manufacturing wheel rim is essential to address the issue of weight reduction while ensuring the load-bearing capacity of the wheel rims during vehicle movement on the road. In this study, the research team designed a 3D model of the wheel rim using Solidworks software.

8p viyamanaka 06-02-2025 2 2   Download

The application of hydro-mechanical transmissions is recently the trend in agricultural vehicles where a continuously variable transmission ratio has advantages. Hydro-mechanical transmissions provide efficient power transfer while maneuverability is still maintained, and therefore, fuel efficiency is enhanced.

11p tuetuebinhan000 23-01-2025 2 2   Download

This research aims to numerically simulate the performance of the tested PC utility poles using Applied Element Method (AEM) and Finite Element Method (FEM). The simulation results demonstrate that both AEM and FEM effectively reproduce the load-displacement relationship observed in the test. Additionally, this study discusses the material models employed in simulations, considering the limitations inherent in numerical modeling.

6p vibenya 31-12-2024 4 2   Download

In this laboratory experiment, you will use SPICE to study sinusoidal waves on lossless transmission lines. Our goal is for you to become familiar with the basic behavior of waves reflecting from loads in transmission lines, and compare the simulations with numeric calculations and the Smith Chart.

30p nhutuanvn91 22-04-2013 125 18   Download

In this thesis, a numerical model with detailed reaction mechanism which is tailored for studying the behaviour of combustion of natural gas has been introduced and validated with available experimental data. The numerical model attempts to comprehensively simulate the physical conditions (temperature and pressure), equivalent ratio, and fuel dilution and strain rate effect in the laminar flames.

158p runthenight05 01-03-2023 22 3   Download

This study focuses on experimental testing and subsequent numerical analysis of impacted and pre-loaded composite coupons and bonded composite scarf joints under varying impact conditions. A methodology will be developed for the numerical modelling of preloaded impact tests to enable capture of critical failure modes and ultimate failure. The main aim is to validate a modelling strategy that will provide accurate failure characterisation of the tested joints using numerical analysis.

185p runthenight05 01-03-2023 19 3   Download

In the course of current research the procedure of obtaining of the piecewise linear vibration systems time and frequency responses have been developed. The method is partly analytical and partly numerical and is based on combining of linear solutions of different sections in a cycle of motion. In a row with the method of obtaining of the exact steady state time and frequency response, also it is provided sensitivity analysis of the vibration isolator.

86p runthenight07 01-03-2023 12 3   Download

The primary goal of this research is accomplishing the BUUAS that can realize functions in the mission profile. In order to achieve this, the project starts with developing elemental aspects of the BUUAS. The configuration and propulsion system are two basic elements that the BUUAS must have to realize successfully operation. Besides, the necessary transition process between water and air must be investigated and carried by a conceived system.

187p runthenight04 02-02-2023 10 2   Download

The aim of this Masters of Engineering (MEng) - Aerospace thesis was to investigate the durability of Piezoelectric Wafer Active Sensors (PWAS) for the health monitoring of composite structures. One significant challenge faced by the aviation industry is the cost and time associated with maintaining aircrafts, in particular, aging airliners. Structural Health Monitoring (SHM) is a possible approach to reduce the high cost of inspection and maintenance.

164p runthenight04 02-02-2023 15 2   Download

The nasal route for drug administration has the potential for local and systemic delivery of a wide variety of therapeutics. Nasal spray drug delivery has the potential to administer drugs to the bloodstream, avoiding the use of painful needles. While there is great potential, studies in the area are limited and somewhat conflicting. This study aimed to support the improvement of nasal drug delivery through experimental work on a model nasal cavity and through experimental characterisation of nasal spray behaviour. Four different brands of nasal spray were investigated.

91p runthenight04 02-02-2023 13 3   Download

The current research is undertaken by performing Computational Fluid Dynamics (CFD) simulations for a 2D aerofoil fitted with a shock control bump at a transonic flow condition. Reynolds-Averaged Navier-Stokes equation coupled with turbulence models is adopted to solve the flowfield. The bump has a conventional geometric feature which consists of a ramp, a crest and a tail, and it has eight variants for which the designed parameters are reasonably specified according to the compressible aerodynamics theory.

84p runthenight04 02-02-2023 10 3   Download

Objectives: Research on the scientific basis to a construct numerical model to simulate the flow and sediment transport on watershed. Application of the built numerical model in some small and medium watersheds.

28p dolphintaletale 23-04-2021 38 6   Download

Although the research direction on NSFD schemes for differential equations have achieved a lot ofresults shown by both quantity and quality of existing research works, real-world situations have always posednew complex problems in both qualitative study and numerical simulation aspects. On the other hand, there aremany differential models that have been established completely in the qualitative aspect but their correspondingdynamically consistent discrete models have not yet been proposed and studied

26p capheviahe29 17-03-2021 29 4   Download

Equivalent inclusion approach is then developed to account for possible diversions, such as non-idealistic geometric forms of the inhomogeneities, imperfect matrix-inclusion contacts, filler dispersions, and when the particular values of the fillers’ properties are unspecified, using available numerical or experimental reference conductivity data for particular composites.

28p capheviahe27 23-02-2021 28 4   Download

Building approximation formulas using equivalentinclusion method to determine the effective values of the conductivity, the elastic modulus of compound-inclusion composite materials and applying numerical methods using finite elements (FE) calculated for some specific material models.

27p capheviahe26 25-01-2021 20 4   Download

This paper presents pith plane dynamic model of a cargo truck. Numerical simulations for determination of a pitch angle and deflection in front and rear suspension under braking on railway crossing are conducted.

9p lucastanguyen 01-06-2020 23 2   Download

The current work attempts to provide an idea of the drop ejection behaviour based on the computation of energies required for droplet formation and splat formation.

13p lucastanguyen 01-06-2020 31 2   Download

This paper presents a dynamic model of a tilting child travel seat. The child seat is presented as a physical pendulum. Thereby the seat in concert with the child can rotate around a cylindrical joint located above its mass center.

6p lucastanguyen 01-06-2020 15 3   Download

The limitation of land in urban area leads to the existence of land slowly omitted and changed to be functioned room. The additional room itself will be reducing thermal comfort in the house.

13p lucastanguyen 01-06-2020 13 2   Download

This paper attempts to develop a numerical maintenance model to determine the optimal inspection regime to be followed for shipboard machinery. The maintenance modelling is carried out by Delay Time Analysis using a down time estimation model.

7p guineverehuynh 21-06-2020 15 2   Download