![](images/graphics/blank.gif)
Plane strain analysis
-
Part 1 book "Stress, strain, and structural dynamics - An interactive handbook of formulas, solutions, and MATLAB toolboxes" includes content: Introduction, static analysis of euler bernoulli beams, static analysis of bars, shafts and strings, buckling analysis of columns, stress analysis in two dimensional problems, static analysis of constrained multispan beams, static analysis of plane trusses, static analysis of plane frames, dynamics of particles and rigid bodies, vibration analysis of one degree of freedom systems.
455p
dianmotminh03
11-06-2024
6
2
Download
-
This paper investigates fracture mechanics in particle-reinforced composites by using the extended finite element method enhanced by the consecutive-interpolation quadrilateral element. These composite materials have discontinuous boundaries such as cracks, voids and hard inclusions.
18p
viamancio
04-06-2024
1
0
Download
-
Part 2 book "Mechanics of materials" includes content: Stresses in beams; analysis of stress and strain; applications of plane stress (pressure vessels and combined loadings); deflections of beams; columns.
344p
muasambanhan06
03-02-2024
3
1
Download
-
The paper discusses the development of a numerical method for a multibraced excavation to estimate strut forces. Two different software were used in the proposed method. Equivalent strut forces were calculated by plane strain analysis on Plaxis 2D.
10p
vicaptainmarvel
21-04-2023
5
2
Download
-
The reticulated InSb pixel array was successfully employed in the design of large format InSb infrared focal plane arrays (IRFPAs) detector, to remove the thermal strain accumulated in InSb IRFPAs with the thermal shock test.
5p
vivalletta2711
11-01-2020
8
1
Download
-
The displacement field is based on classical beam theory. Both plane stress and plane strain state are used to achieve constitutive equations. The governing equations are derived from Lagrange’s equations. Ritz method is applied to obtain the critical buckl. ing loads of thin-walled beams. Numerical results are compared to those in available literature and investigate the effects of fiber angle, length-to-height’s ratio, boundary condition on the critical buckling loads of thin-walled channel beams
11p
elandorr
05-12-2019
10
0
Download
-
Ground improvement technique by prefabricated vertical drain (PVD) in combination with vacuum preloading is widely used to facilitate consolidation process and reduce residual settlement. However, this technique seem hardly be estimated by both analytical method and numerical method because it has complex boundary conditions (such as vacuum pressure changing with time). Moreover, lateral displacements caused by this technique are also significant problem.
18p
chauchaungayxua1
03-12-2019
43
1
Download
-
Using the formulated element, the critical load and equilibrium path are computed with the aid of the bracketing procedure and the arc-length control method, respectively. Numerical examples show that the proposed element is capable to give accurate results with a smaller number of elements comparing to the elements previously used in the examples. The effect of the nonlinear term used in the local strain expression on the numerical results is also investigated and highlighted.
17p
thienthanquydu
19-10-2018
42
0
Download
-
The following will be discussed in this chapter: Introduction, transformation of plane stress, principal stresses, maximum shearing stress, mohr’s circle for plane stress, general state of stress, application of mohr’s circle to the three- dimensional analysis of stress, yield criteria for ductile materials under plane stress, fracture criteria for brittle materials under plane stress, stresses in thin-walled pressure vessels.
40p
nomoney9
04-04-2017
57
2
Download
-
(bq) part 2 book "mechanics of materials" has contents: stresses in beams (advanced topics), applications of plane stress (pressure vessels, beams, and combined loadings), analysis of stress and strain, statically indeterminate beams, deflections of beams, columns, review of centroids and moments of inertia.
571p
bautroibinhyen20
06-03-2017
73
9
Download
-
(bq) part 2 book "a first course in the finite element method" has contents: practical considerations in modeling; interpreting results; and examples of plane stress–strain analysis; three dimensional stress analysis, plate bending element, heat transfer and mass transport, thermal stress, structural dynamics and time dependent heat transfer,... and other contents.
595p
bautroibinhyen19
02-03-2017
69
7
Download
-
(bq) part 2 book "mechanics of materials" has contents: analysis of stress and strain; applications of plane stress (pressure vessels, beams, and combined loadings); deflections of beams; statically indeterminate beams; columns; review of centroids and moments of inertia.
477p
bautroibinhyen19
02-03-2017
41
3
Download
-
(bq) part 1 book "mechanics of materials" has contents: stresses in beams (advanced topics); analysis of stress and strain, applications of plane stress (pressure vessels, beams, and combined loadings), deflections of beams, statically indeterminate beams, columns, review of centroids and moments of inertia.
577p
bautroibinhyen19
02-03-2017
52
7
Download
-
(bq) part 1 book "the finite element method (volume 1: the basis)" has contents: some preliminaries - the standard discrete system, a direct approach to problems in elasticity; plane stress and plane strain; axisymmetric stress analysis; the patch test, reduced integration, and non-conforming elements,... and other contents.
322p
bautroibinhyen19
27-02-2017
53
4
Download
-
The PLAXIS 2D program is a special purpose two-dimensional finite element program used to perform deformation and stability analysis for various types of geotechnical applications. Real situations may be modelled either by a plane strain or an axisymmetric model. The program uses a convenient graphical user interface that enables users to quickly generate a geometry model and finite element mesh based on a representative vertical cross section of the situation at hand. Users need to be familiar with the Windows environment.
0p
daicatruongpro
02-05-2013
94
10
Download