Firewall Management Interface

Chia sẻ: Tuan Bui Nghia | Ngày: | Loại File: PDF | Số trang:7

Thêm vào BST

Báo xấu

75
lượt xem 15
download

Download Vui lòng tải xuống để xem tài liệu đầy đủ

This section provides an overview and some examples of these interfaces. Managing Firewalls with a CLI A CLI enables you to use a specific instruction set to configure the firewall

Chủ đề:

Bình luận(0) Đăng nhập để gửi bình luận!

Lưu

Nội dung Text: Firewall Management Interface

Firewall Management Interface Modern firewalls come with two administrative interfaces: • The CLI • The GUI (typically, but not necessarily, web based) This section provides an overview and some examples of these interfaces. Managing Firewalls with a CLI A CLI enables you to use a specific instruction set to configure the firewall. Most firewalls require the end user to do the initial configuration of the firewall (inputting in the basic network information such as IP address, net mask, default gateway, and possibly an administrative password) via CLI before the end user can switch over to the GUI. Linux's NetFilter is, for the most part, configured through a CLI, although there do exist several products that allow for configuration of NetFilter-based firewalls through a GUI. CLIs require knowledge of the command set in the firewall product. For example, to configure NetFilter, use the IPTables CLI to allow inbound Secure Shell (SSH), e-mail, and web traffic (using TCP ports 22, 25, and 80, respectively) and deny all other traffic requires the configuration in Example 11-1. Example 11-1. Configuring NetFilter with IPTables [View full width] # iptables -P INPUT DENY # iptables -P OUTPUT ACCEPT # iptables -P FORWARD ACCEPT # iptables -A INPUT -i lo -j ACCEPT # iptables -A INPUT -p tcp -s 0.0.0.0/0 -d 10.16.17.202 --dport 22 -m state -- state NEW - j ACCEPT # iptables -A INPUT -p tcp -s 0.0.0.0/0 -d 10.16.17.202 --dport 25 -m state -- state NEW -j ACCEPT # iptables -A INPUT -p tcp -s 0.0.0.0/0 -d 10.16.17.202 --dport 80 -m state -- state NEW -j ACCEPT
# iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # iptables -A INPUT --reject-with icmp-host-prohibited -j REJECT Example 11-2 provides a similar configuration with the PIX command set. Example 11-2. Configuring a PIX gandalf(config)# access-list acl_test permit tcp any host 10.16.17.202 eq ssh gandalf(config)# access-list acl_test permit tcp any host 10.16.17.202 eq smtp gandalf(config)# access-list acl_test permit tcp any host 10.16.17.202 eq 80 gandalf(config)# access-list acl_test permit icmp any any gandalf(config)# access-list acl_test deny ip any any gandalf(config)# show access-list acl_test access-list acl_test; 5 elements access-list acl_test line 1 permit tcp any host 10.16.17.202 eq ssh (hitcnt=0) access-list acl_test line 2 permit tcp any host 10.16.17.202 eq smtp (hitcnt=0) access-list acl_test line 3 permit tcp any host 10.16.17.202 eq www (hitcnt=0) access-list acl_test line 4 permit icmp any any (hitcnt=0) access-list acl_test line 5 deny ip any any (hitcnt=0) Knowledge of the command set is critical to effectively configure a firewall through a CLI. Many vendors (and third parties) have worked hard to reduce the configuration of a firewall to a more simplistic method. When the initial configuration is done (supplying the firewall software with an IP address and net mask), the end user can immediately switch to a more graphical method of configuring the firewall. Managing Firewalls with a GUI A GUI provides a more-user-friendly interface to configure the firewall. Some firewalls are configured through a direct interface on the host, such as Symantec Norton Internet Security shown in Figure 11-1 and Figure 11-2, before the firewall is active. Some come with a preconfigured IP address and an administrative password to be used for access by the end user during initial configuration (such as Linksys or the PIX 501 and 506E series systems). Figure 11-1. Symantec Internet Security Configuration [View full size image]
Figure 11-2. Symantec Firewall Configuration [View full size image]
The PIX Device Manager (for PIX operating systems up to versions 6.3(5)), known as the Cisco Adaptive Security Device Manager in PIX version 7.0, is a Java applet that is downloaded from the PIX or ASA device and runs locally through the client browser. Figure 11-3 shows the PIX Device Manager screen. Figure 11-3. Cisco PIX Device Manager [View full size image]
The information is presented in a more natural fashion to the end user in the form of graphics and graphs for performance. Not to be outdone, there are GUIs for Linux's IPTables firewall software. Some are web based (such as Webmin), and some are applications running on the Linux system itself (such as Firestarter or FW-Builder). Firestarter provides a simple, easy-to-use interface for IPTables, as shown in Figure 11-4. Figure 11-4. Firestarter for IPTables [View full size image]
Webmin provides a method by which the firewall can be managed through a web browser interface, which is more convenient than an application that can only be viewed on an X Windows-enabled server. Figure 11-5 shows this interface. Figure 11-5. Webmin IPTables Rules Interface [View full size image]
Interface Preference Whether it is through a CLI or through a GUI, the management of a firewall can range from the highly complex to the relatively easy. Typically, novice users start by administering the firewall through a GUI. Over time, as their experience level and comfort level with the firewall increase, they may find it more convenient to use a CLI. One significant benefit of a CLI over a GUI is that the CLI is available through Telnet and SSH sessions as well as connected directly to the serial port. This becomes important when considering how access to the firewall management interface will be controlled.