Practical TCP/IP and Ethernet Networking- P8

Chia sẻ: Cong Thanh | Ngày: | Loại File: PDF | Số trang:5

Thêm vào BST

Báo xấu

72
lượt xem 3
download

Download Vui lòng tải xuống để xem tài liệu đầy đủ

Practical TCP/IP and Ethernet Networking- P8: The transmitter encodes the information into a suitable form to be transmitted over the communications channel. The communications channel moves this signal as electromagnetic energy from the source to one or more destination receivers. The channel may convert this energy from one form to another, such as electrical to optical signals, whilst maintaining the integrity of the information so the recipient can understand the message sent by the transmitter....

Chủ đề:

Bình luận(0) Đăng nhập để gửi bình luận!

Lưu

Nội dung Text: Practical TCP/IP and Ethernet Networking- P8

4KZ]UXQOTM L[TJGSKTZGRY )OXI[OZ Y]OZINOTM In a circuit switched process a continuous connection is made across the network between the two different points. This is a temporary connection, which remains in place as long as both parties wish to communicate, that is until the connection is terminated. All the network resources are available for the exclusive use of these two parties whether they are sending data or not. When the connection is terminated the network resources are released for other users. A telephone call is an example of a circuit switched connection. The advantage of circuit switching is that the users have an exclusive channel available for the transfer of their data at any time while the connection is made. The obvious disadvantage is the cost of maintaining the connection when there is little or no data being transferred. Such connections can be very inefficient for the bursts of data that are typical of many computer applications. 6GIQKZ Y]OZINOTM Packet switching systems improve the efficiency of the transfer of bursts of data, by sharing the one communications channel with other similar users. This is analogous to the efficiencies of the mail system as discussed in the following paragraph. When you send a letter by mail you post the stamped, addressed envelope containing the letter in your local mailbox. At regular intervals the mail company collects all the letters from your locality and takes them to a central sorting facility where the letters are sorted in accordance with the addresses of their destinations. All the letters for each destination are sent off in common mailbags to those locations, and are subsequently delivered in accordance with their addresses. Here we have economies of scale where many letters are carried at one time and are delivered by the one visit to your street/locality. Efficiency is more important than speed, and some delay is normal – within acceptable limits. Packet switched messages are broken into a series of packets of certain maximum size, each containing the destination and source addresses and a packet sequence number. The packets are sent over a common communications channel, possibly interleaved with those of other users. All the receivers on the channel check the destination addresses of all packets and accept only those carrying their address. Messages sent in multiple packets are reassembled in the correct order by the destination node. All packets do not necessarily follow the same path. As they travel through the network they may get separated and handled independently from each other, but eventually arrive at their correct destination. For this reason, packets often arrive at the destination node out of their transmitted sequence. Some packets may even be held up temporarily (stored) at a node, due to unavailable lines or technical problems that might arise on the network. When the time is right, the node then allows the packet to pass or be ‘forwarded’. *GZGMXGSY GTJ \OXZ[GR IOXI[OZY Packet switched services generally support two types of service viz. datagrams and virtual circuits. In a self contained local area network all packets will eventually reach their destination. However, if the packet is to be switched ACROSS networks i.e. on an internetwork – such as a wide area network – then a routing decision must be made. There are two approaches that can be taken. The first is referred to as a DATAGRAM service. The approach is to allow each packet to be independently routed. The destination
6XGIZOIGR :)6/6 GTJ +ZNKXTKZ 4KZ]UXQOTM address incorporated in the data header will allow the routing to be performed. There is no guarantee when any packet will arrive at its destination, and they may well be out of sequence. The principle is similar to the mail service. You may send four postcards from your holiday in the South of France, but there is no guarantee that they will arrive in the same order that you posted them. If the recipient does not have a telephone, there is no easy method of determining that they have, in fact, been delivered. Such a service is called an UNRELIABLE service. This word is not used in its everyday context, but rather refers to the fact that there is no mechanism for informing the sender that the packet had not been delivered. The service is also called connectionless since a connection is not made for each packet. The second approach is to setup a connection between transmitter and receiver, and to send all packets of data along this connection or VIRTUAL CIRCUIT. Whilst this might seem to be in conflict with the earlier statements on circuit switching, it should be quite clear that this does NOT imply a permanent circuit being dedicated to the one packet stream of data. Rather, the circuit shares its capacity with other traffic. The important point to note is that the route for the data packets to follow is taken up-front when all the routing decisions are taken. The data packets just follow that pre-established route. This service is known as RELIABLE and is also referred to as a connection oriented service or COS. :_VKY UL TKZ]UXQY 2UIGR GXKG TKZ]UXQY 2'4Y LANs are characterized by high-speed transmission over a restricted geographical area. Thick Ethernet (10Base5), for example, operates at 10 Mb/s over a maximum distance of 500 m before the signals need to be boosted. This is illustrated in Figure 2.2. Figure 2.2 Example of LAN =OJK GXKG TKZ]UXQY ='4Y While LANs operate where distances are relatively small, wide area networks (WANs) are used to link LANs that are separated by large distances that range from a few tens of meters to thousands of kilometers. WANs normally use the public telecommunication system to provide cost-effective connection between LANs. Since these links are supplied by independent telecommunications utilities, they are commonly referred to (and illustrated as) a ‘communications cloud’. Special equipment called gateways have been developed for this type of activity, which store the message at LAN speed and transmit it across the ‘communications cloud’ at a lower speed. When the entire message has been received at the remote LAN, the message is reinserted at LAN speed. A typical speed at which a WAN interconnects is 9600 bps to 45 Mbps. This is shown in Figure 2.3.
4KZ]UXQOTM L[TJGSKTZGRY Figure 2.3 WAN concept If reliability is needed for a time critical application, WANs can be considered quite unreliable, as delay in the information transmission is varied and wide. For this reason, WANs can only be used if the necessary error detection/ correction software is in place, and if propagation delays can be tolerated within certain limits. 3KZXUVUROZGT GXKG TKZ]UXQY 3'4Y An intermediate type of a network – MANs – operate at speeds ranging from 56 kbps to 100Mbps – typically a higher speed than WANs but slower than LANs. MANs use fiber optic technology to communicate over distances of up to several hundred kilometers. They are normally used by telecommunication service providers within cities. )U[VROTM XGZOU The coupling ratio provides an academic yardstick for comparing the performance of these different kinds of networks. It is useful to give us an insight as to the way that each network needs to operate. Coupling ratio α = τ / T Where τ Propagation delay for packet T Average packet transmission time α =1 indicates a WAN This is illustrated in the following examples and Figure 2.4. 200 m LAN: With a propagation delay of about 1 mS, a 1000 byte packet takes about 0.8 ms to transmit at 10 Mbps. Therefore α is about 1 mS/0.8 ms or 1/800 which is very much less than 1. This means that for a LAN the packet quickly reaches the destination and the transmission of the packet then takes say hundreds of times longer to complete. 200 km MAN: With a propagation delay of about 1 mS, a 4000 byte packet takes about 0.4 ms to transmit at 100 Mbps. Therefore α is about 1 mS/0.4 ms or 2.4 which is about the order of 1. This means that for a MAN the packet reaches the destination then may only take about the same time again to complete the transmission.
6XGIZOIGR :)6/6 GTJ +ZNKXTKZ 4KZ]UXQOTM 100 000 km WAN: Propagation delay about 0.5–2 seconds, a packet of 128 bytes takes about 10 ms to transmit at 1 Mbps. Therefore α is about 1 S/10 ms or 100. This means that for a WAN the packet reaches the destination after a delay of 100 times the packet length. Figure 2.4 Coupling ratios
4KZ]UXQOTM L[TJGSKTZGRY considered unlikely that equipment from other manufacturers would be included in the network. In contrast, open systems are those, which conform to specifications and guidelines, which are ‘open’ to all. This allows equipment from any manufacturer, who claims to comply with that standard, to be used interchangeably on the standard network. The benefits of open systems include wider availability of equipment, lower prices and easier integration with other components. :NK UVKT Y_YZKSY OTZKXIUTTKIZOUT XKLKXKTIK SUJKR 59/ SUJKR Faced with the proliferation of closed network systems, in 1978 the International Standards Organization (ISO) defined a ‘Reference Model for Communication between Open Systems’, which has become known as the open systems interconnection (OSI) model, or simply as the ISO/OSI model (ISO 7498). OSI is essentially a data communications management structure, which breaks data communications down into a manageable hierarchy of seven layers. Each layer has a defined purpose and interfaces with the layers above it and below it. By laying down standards for each layer, some flexibility is allowed so that the system designers can develop protocols for each layer independent of each other. By conforming to the OSI standards, a system is able to communicate with any other compliant system, anywhere in the world. It should be realized at the outset that the OSI reference model is not a protocol or set of rules for how a protocol should be written but rather an overall framework in which to define protocols. The OSI model framework specifically and clearly defines the functions or services that have to be provided at each of the seven layers (or levels). Since there must be at least two sites to communicate, each layer also appears to converse with its peer layer at the other end of the communication channel in a virtual (‘logical’) communication. These concepts of isolation of the process of each layer, together with standardized interfaces and peer-to-peer virtual communication, are fundamental to the concepts developed in a layered model such as the OSI model. The OSI layering concept is shown in Figure 2.5. Figure 2. 5 OSI layering concept The actual functions within each layer are provided by entities which are abstract devices, such as programs, functions, or protocols, that implement the services for a particular layer on a single machine. A layer may have more than one entity – for example a protocol entity and a management entity. Entities in adjacent layers interact