ASTM Standards

This specification covers five grades of zinc-coated, steel wire strand, composed of a number of round, steel wires, with four weights of zinc coatings, suitable for use as guys, messengers, span wires, and for similar purposes.

5p hth_hn_vn 10-12-2023 5 3   Download

This specification covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by ASTM: Specifications A240/A240M, A263, A264, A265, A666, A693, A793, and A895.

26p hth_hn_vn 10-12-2023 4 3   Download

This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under the latest revision of each of the following ASTM specifications: A276, A314, A458, A473, A477, A479/ A479M, A564/A564M, A565/A565M, A582/A582M, A638/ A638M, A705/A705M, and A831/A831M.

13p hth_hn_vn 10-12-2023 3 3   Download

This specification covers deformed steel wire which has been cold-worked by drawing, rolling, or both drawing and rolling, to be used as produced, or in fabricated form, for the reinforcement of concrete in sizes having nominal crosssectional areas not less than 6.45 mm2 [0.01 in.2 ].

6p hth_hn_vn 10-12-2023 4 3   Download

This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to carbon and alloy steel bars under each of the following ASTM specifications (or under any other ASTM specification which invokes this specification or portions thereof).

16p hth_hn_vn 10-12-2023 7 4   Download

"Standard Specification for Ferrovanadium" covers one grade of ferrovanadium. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

3p hth_hn_vn 10-12-2023 5 3   Download

This specification covers a group of requirements which, with the exceptions of Section 6.3, Section 14, Section 21, and Section 22, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification specifies different requirements, in which case the requirement of the product specification shall prevail.

9p hth_hn_vn 10-12-2023 9 3   Download

This specification covers general requirements that shall apply to stainless wire and wire rods. Wire rods are a semifinished product intended primarily for the manufacture of wire. Wire is intended primarily for cold forming, including coiling, stranding, weaving, heading and machining as covered under the latest revision of each of the following ASTM specifications: A313/A313M, A368, A478, A492, A493, A580/A580M and A581/A581M.

6p hth_hn_vn 10-12-2023 4 3   Download

This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.

2p hth_hn_vn 10-12-2023 3 3   Download

This specification covers untreated and heat-treated carbon and alloy steel forgings for general industrial use. Other ASTM specifications for forgings are available for specific applications such as pressure vessels, railroad use, turbine generators, gearing, and others involving special temperature requirements.

9p hth_hn_vn 10-12-2023 6 4   Download

This practice covers the procedure for designating (within ASTM specifications) standard grades of flat-rolled electrical steels made to specified maximum values of specific core loss. This practice applies to magnetically soft irons and steel (low-carbon steels and alloys of iron with silicon, aluminum, and other alloying elements) where a core loss measurement at a stated peak value of alternating induction and a stated frequency, such as 1.5 T (15 kG) and 60 Hz, is normally used to grade the material.

4p hth_hn_vn 10-12-2023 5 3   Download

This specification covers the chemical, mechanical, and physical requirements for available wrought carbon tool steel products. These products, which include hot- or cold-finished bar, plate, sheet, rod, wire, or forgings, are normally fabricated into tools, dies, or fixtures. The selection of a material for a particular application will depend upon design, service conditions, and desired properties.

12p hth_hn_vn 10-12-2023 5 5   Download

This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to steel castings for pressure-containing parts under each of the following ASTM specifications.

12p hth_hn_vn 10-12-2023 6 4   Download

This specification covers a group of requirements that are mandatory requirements of the following steel casting specifications issued by ASTM. If the product specification specifies different requirements, the product specification shall prevail.

11p hth_hn_vn 10-12-2023 6 4   Download

This specification covers two classes of flanged and cold-bending quality cold-worked straight-seam single or double welded austenitic steel pipe intended for hightemperature and general corrosive services.

7p hth_hn_vn 10-12-2023 4 4   Download

This specification covers structural quality alloy steel plates; The plates are usually specified to chemical composition requirements, but tensile properties may also be specified.

4p hth_hn_vn 10-12-2023 7 4   Download

This specification covers standard nominal sizes and size tolerances of screened ferroalloy and alloy additive products. This specification provides a range of sizes as referenced in all ASTM specifications for ferroalloys and alloy additives.

4p hth_hn_vn 10-12-2023 8 4   Download

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

3p hth_hn_vn 10-12-2023 3 3   Download

This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM.

63p hth_hn_vn 10-12-2023 4 2   Download

The prediction of the expected long-term performance of concrete exposed to sewage and similar materials can be difficult as it is affected by a large number of parameters. In addition, the deterioration process in concrete is generally slow. The focus of the study was to ascertain the life expectancy of concrete septic tanks located in rural Victoria. In developing the accelerated test method, ASTM C 192, ASTM C 452, ASTM C 1293 and ASTM C 109 standard procedures were adopted wherever possible.

172p runthenight05 01-03-2023 3 2   Download