Configuring static routes

Configuration requirements: (65 marks) 1. Calculating the subnet addressing for the lab using the VLSM technique and note all information needed on the topology.(10) 2. Perform Basic Router Configurations all Routers.(5) 3. In each LAN, configure the second usable host address for PC1 and the last usable host address for PC2.(5) 4. Enable routing on HQ, BRANCH1, and BRANCH2 by using the dynamic routing protocol as EIGRP.(Using wildcard mask, AS number = 1).(30) 5. Configure the static route for the Internet connection (10) 6.

2p anhchangxuixeo1002 14-03-2013 78 6   Download

Part I: 1. Cabling as the diagram 2. Calculating all the subnets for the diagram. Note: 172.X.0.0/16 where X is the sequence number in the students list. 3. Basic router config for R1, R2, R3 and ISP: Password for console=cisco Password for enable mode=ccna Password for vty =class 4. Install OSPF as the routing protocol on R1,R2 and R3. DO NOT advertise all subnets to the ISP router: process number = 10, area number=0 ) 5. Configure the static route on R1,R2 and R3...

1p anhchangxuixeo1002 14-03-2013 78 6   Download

Basic router config for R1, R2, R3 and ISP: Password for console=cisco Password for enable mode=ccna Password for vty =class 4. Install OSPF as the routing protocol on R1,R2 and R3. DO NOT advertise all subnets to the ISP router: process number = 10, area number=0 ) 5. Configure the static route on R1,R2 and R3 for the Internet connection

1p phutran76 16-07-2012 86 16   Download

Calculating the subnet addressing for the lab using the VLSM technique and note all information needed on the topology.(60 marks) In each LAN, configure the second usable host address for PC1 and the last usable host address for PC2.(5 marks) Perform Basic Router Configurations all Routers.(10 marks) Enable routing on R1, R2, R3 and R4 by using the static routing protocol.(5 marks)

2p phutran76 16-07-2012 72 6   Download

Configuration requirements: (8 marks) 1. Calculating the subnet addressing for the lab using the VLSM technique and note all information needed on the topology. 2. In each LAN, configure the second usable host address for PC1 and the last usable host address for PC2. 3. Perform Basic Router Configurations all Routers. 4. Enable routing on R1, R2, R3 and R4 by using the static routing protocol.

2p phutran76 16-07-2012 83 14   Download

Calculating the subnet addressing for the lab using the VLSM technique and note all information needed on the topology. In each LAN, configure the second usable host address for PC1 and the last usable host address for PC2. Perform Basic Router Configurations all Routers. Enable routing on R1, R2, R3 and R4 by using the static routing protocol.

2p phutran76 16-07-2012 72 6   Download

Which of the following are required when adding a network to the OSPF routing process configuration? (Choose three.) In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network? A network administrator is analyzing routing update behavior on a network that has both EIGRP and OSPF configured on all routers. Both protocols appear in the output of show ip protocols. However, only EIGRP internal routes appear in the routing tables. Which statement correctly explains the scenario?...

5p phutran76 06-06-2012 158 30   Download

What is an advantage of the NAT-PT technique for transitioning between IPv4 and IPv6? All mappings are static. Globally routable IPv4 addressing is not required. DNS is not required. No configuration is required on end nodes. How do IPv6 enabled routers handle packet fragmentation? IPv6 routers do not perform packet fragmentation. OSPFv3 has a mechanism for determining the optimal packet size and dynamically adjusting the packet size. IPv6 routers do not perform packet fragmentation. CDP is used to discover the correct packet size for any given traffic flow....

10p danhson1409 26-12-2010 144 13   Download

Các chế độ cấu hình: Router (chế độ user mode), Routerenable (vào chế độ Privileged EXEC Mode), Router#configure terminal (vào chế độ Configuration Mode). Cấu hình đặt tên và password cho router: Router(config)#hostname tên_muốn_đặt (đặt tên cho router), Router(config)#enable password pass_muốn đặt (cấu hình pass ko mã hóa), Router(config)#enable secret pass_muốn_đặt (cấu hình pass được mã hóa bằng MD5).

4p thuyte 24-08-2010 335 100   Download