Finite element simulation

This thesis deals with the finite element simulation of spot welded joint in crash analysis. Spot welding is a very common joining process in the automotive industry. It is cost effective and it provides a very fast production rate of automotive body components. Despite this advantage, spot welds are very susceptible to various types of loading conditions. Therefore they are prone to failure, if not designed properly, during their service life time. Therefore it is very important to understand the behaviour of spot welds and their failure characteristics.

243p runthenight05 01-03-2023 9 4   Download

This thesis investigates the SPH capability available in the commercial Finite Element (FE) code LS-DYNA®, for water impact problems. Experiments have been conducted on rigid wedges impacting water, which were then simulated with the SPH method. Although certain limitations were experienced with the experimental results, a positive correlation was observed with the numerical technique, thus establishing SPH as a promising method for crashworthiness design.

176p runthenight07 01-03-2023 9 3   Download

This research investigates integrated drive topologies for Switched Reluctance Motors (SRMs). During the research project, three new power electronic topologies are proposed and simulated via extensive simulations in finite element modelling software (Maxwell) and MATLAB/Simulink.

120p runthenight04 02-02-2023 9 3   Download

The final goal of the work is to provide useful recommendations and guidelines for the design of a cold plug for the emergency draining system of a molten salt reactor. Some numerical thermal simulations were performed with ANSYS mechanical (Finite Element Method) to be compared with results of the experiments and to make extrapolations for a new component to be used in a reactor.

12p christabelhuynh 29-05-2020 36 3   Download

Strain-softening material models have conventionally had a pathological mesh sensitivity in finite element simulations and composite materials are indifferent to this problem. Spurious localization is inherent to the structural problem in strain-driven softening.

16p tohitohi 19-05-2020 10 0   Download

In this paper, buckling behavior of aluminum cylindrical shell with rectangular cutout, subjected to axial pressure was studied by means of finite element simulations. The effects of geometric parameters (R, t, a, b and L) on the first buckling mode capacity of the shell were studied.

12p tohitohi 19-05-2020 11 1   Download

Simulation and visualization of the mechanical components have become a predominant phase during the design and the production stages. Several means are used to improve the design and to reduce study time.

8p tohitohi 19-05-2020 20 3   Download

In this study, a 3D finite element model of an intact mandible was used for the simulation of the movement of the lower jaw and analysis of the effects of TemporoMandibular Joint (TMJ) prosthesis replacement on the jaw movement. Seven bundles of muscle fibers were inserted in their appropriate positions following anatomical data.

10p tohitohi 19-05-2020 25 1   Download

Portland cement concrete (PCC) / asphalt concrete (AC) bonded components are seen in both conventional pavement structures as well as overlays. Due to the environmental and traffic loads, cracks occur at the interface of the PCC and AC layers and finally, may propagate through the interface or one of the layers.

14p tohitohi 19-05-2020 20 3   Download

The results of this paper can be used for standardization of the fracture in underwater structures containing V-notched components.

10p tohitohi 19-05-2020 9 0   Download

Head injuries are among the dangerous injuries which are common in all sport types. In the present study, the dynamic response of a punch to the head of a Wushu fighter was simulated by modeling the human head in ABAQUS software.

10p tohitohi 19-05-2020 14 0   Download

In this paper, an extended forming limit stress diagram (EFLSD) was applied to predict neck initiation failure in tube hydroforming of metal bellows. The proposed EFLSD was used in conjunction with ABAQUS/ EXPLICIT finite element simulations to predict the onset of necking in tube hydroforming of metal bellows.

10p tohitohi 19-05-2020 17 1   Download

The fatigue failure around rail-end-bolt holes is particularly dangerous since it leads to derailment of trains and consequently to inevitable accidents. It is well-known that the fatigue life of structural holed components, subjected to cyclic load, can be increased by generating compressive hoop stresses around the holes.

18p tohitohi 19-05-2020 17 1   Download

Collide of two objects or impact, is one of the main damage initiation reasons. In this paper, impact and damage behavior of elastic and visco-elastic bodies are investigated numerically using the finite element analyses.

8p tohitohi 19-05-2020 12 1   Download

This thesis aims to develop finite element models for studying vibration of the 2D-FGM beam. These models require high reliability, good convergence speed and be able to evaluate the influence of material parameters, geometric parameters as well as being able to simulate the effect of shear deformation on vibration characteristics and dynamic responses of the 2D-FGM beam.

27p xacxuoc4321 08-07-2019 50 8   Download

THE CONTACT PROBLEM IN THE SIMULATED DESIGN CREATED BY THE FINITE ELEMENT METHOD Bài báo này giới thiệu về các nghiên cứu lý thuyết xoay quanh vấn đề tiếp xúc giữa các vật thể, và sự áp dụng các thành tựu của những nghiên cứu này khi thiết kế mô phỏng bài toán có tiếp xúc bằng phần mềm ứng dụng phương pháp phần tử hữu hạn.

5p phalinh18 18-08-2011 101 8   Download