![](images/graphics/blank.gif)
International electrotechnical commission
-
Lecture Software process improvement: Lesson 33 provide students with knowledge about: ISO/IEC 12207:2008; information technology software life cycle processes; international standards organization (ISO); international electrotechnical commission (IEC);... Please refer to the detailed content of the lecture!
62p
hanlamcoman
26-11-2022
7
2
Download
-
Tiêu chuẩn ISO/IEC 17025 (International Organization for Standardization/ International Electrotechnical Commission) là một trong những thước đo quan trọng chứng nhận cho phòng thí nghiệm đạt tiêu chuẩn quốc tế. Trong nghiên cứu này, các phương pháp lấy mẫu lúa phục vụ thử nghiệm xác định locus gen mục tiêu đã được thiết lập.
4p
vithomas2711
17-03-2020
48
2
Download
-
This guide has been written for electrical Engineers who have to design, select electrical equipment, install these equipment and, inspect or maintain low-voltage electrical installations in compliance with international Standards of the International Electrotechnical Commission (IEC). “Which technical solution will guarantee that all relevant safety rules are met?” This question has been a permanent guideline for the elaboration of this document.
564p
nmtinh
09-06-2015
104
35
Download
-
This guide has been written for electrical Engineers who have to design, realize, inspect or maintain electrical installations in compliance with international Standards of the International Electrotechnical Commission (IEC).
492p
ductt47
21-10-2013
105
25
Download
-
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest.
130p
phamhongnhungp
25-04-2013
96
14
Download
-
Vào thế chiến thứ II, các kỹ thuật viên đã sử dụng hệ nhị phân để biểu hiện trạng thái của các nguồn điện cho những khoá chuyển mạch. Họ sử dụng ký tự 1 để biểu thị trạng thái ON và ký tự 0 để biểu thị trạng thái OFF. Năm 1973, Uỷ ban Kỹ thuật điện quốc tế IEC (International Electrotechnical Commission) đã quyết định kết hợp hai ký tự này lại trở thành một biểu tượng với vòng tròn khuyết và một đường thẳng nằm bên trong để biểu thị trạng thái “nghỉ” (standby). Viện kỹ sư điện...
3p
bibocumi26
13-01-2013
57
1
Download
-
There are a number of good reasons to ground but primary among them is to ensure personnel safety. The following agencies and organizations all have recommendations and / or standards for grounding, to ensure that personnel safety is being protected.
20p
ndkhuong177
14-07-2012
98
18
Download
-
CÁC MÔ HÌNH ỨNG DỤNG ĐIỀU KHIỂN PHÂN TÁN 7.1 IEC-61131 IEC (International Electrotechnical Commission) là một tổ chức toàn cầu bao gồm các hội đồng ở các quốc gia. Mục tiêu của tổ chức này là thúc đẩy công việc chuẩn hoá trong lĩnh vực điện và điện tử. IEC 61131 là tiêu chuẩn về bộ điểu khiển khả trình PLC và các thiết bị ngoại vi đi kèm với nó. Chuẩn IEC 61131 bao gồm 9 phần, trong đó các phần 1 đến 5 là quan trọng nhất: ...
10p
suatuoi_thomngon
31-07-2011
167
55
Download
-
Standards are appointments and may become enforceable by jurisdictional law and administrative regulations through signed contracts (for instance a sales contract) and can be understood to be ‘‘approved technology rules’’. The general features of standards are, in short: . . . . . . Standards are a service for technology. Standards are an economic and a technical form of cooperation (see also DIN 820 Part 1).
11p
congdat261
08-11-2010
78
7
Download