Surface properties of materials

In this paper, the Timoshenko beam theory is developed for bending analysis of functionally graded beams having porosities. Material properties are assumed to vary through the height of the beam according to a power law.

13p viyoko 24-09-2024 2 1   Download

This study evaluates the effectiveness of using crushed construction and demolition waste as reactive media for applying in Permeable Reactive Barriers to treat contaminated groundwater by landfill leachate. Modern analytical methods such as SEM and EDX were used to analyze the physicochemical properties of crushed demolition waste, demonstrating that the material has a porous structure on the surface that is suitable for the targeted heavy metal adsorption.

9p vifaye 20-09-2024 3 1   Download

Harvesting microalgae by centrifugation and filtration is very costly, affecting technical and economical feasibility of downstream processing of algal biomas to bioproducts. Flocculation is a potential technique for recovery of algae biomass. Particularly, flocculation using magnetic nanoparticles offers high separation efficiency due to their high surface area and magnetic properties. I

10p dianmotminh02 03-05-2024 5 1   Download

The objectives of the present study are: Justifying the possibility of using laser cladding technology as a repair method for refurbishment of worn railway axles without jeopardizing their fatigue properties; Analysis of crack initiation and propagation in laser clad samples.

130p runthenight07 01-03-2023 6 3   Download

Once the mechanical properties of printed TPU are characterised, a novel, low cost, and environmentally friendly method for concrete casting using printed TPU moulds is proposed in this thesis. Additively manufactured TPU mould is developed to cast complex concrete structures. A planar topologically optimized cantilever and a free-form 3D column are cast using the proposed TPU mould. Good surface quality is obtained for the cast concrete elements, and the moulds can be reused many times after cleaning.

98p runthenight04 02-02-2023 8 4   Download

In this thesis, we research and fabricate AgNDs, AgNFs, AuNFs structures on silicon by chemical deposition and electrochemical deposition method for the main purpose of using as SERS substrate. To this target, we have studied the morphology, structure and some properties of the nanostructures produced.

26p extraenglish 24-05-2021 26 4   Download

To study relation of molecular structural changing between polypropylene microcomposite system and the particle fillers with varies phase interactions by using solid-state NMR(ssNMR) spectra.Therein,emphasizing the molecular flexibility on mechanical properties of materials.

22p capheviahe27 23-02-2021 10 2   Download

In this thesis, we research and fabricate AgNDs, AgNFs, AuNFs structures on silicon by chemical deposition and electrochemical deposition method for the main purpose of using as SERS substrate. To this target, we have studied the morphology, structure and some properties of the nanostructures produced.

26p capheviahe27 23-02-2021 33 4   Download

Semiconductors nanoparticles have quantum size effects and non-linear optical characteristics as well as high quantum efficiency, making them next-generation materials that can be applied in various optoelectronic devices. Semiconductor nanoparticles have attracted much attention because of their novel electric and optical properties originating from surface and quantum confinement effects.

5p tamynhan5 10-12-2020 14 2   Download

In this study, TiO2 was used as an additive for polyaniline, considered to be a matrix polymer. The nanocomposite film was fabricated electrochemically on metal surfaces (mild steel and stainless steel). The electrochemical properties of polyaniline could be seen on the cyclic voltammogram.

8p tamynhan8 04-11-2020 11 3   Download

The feedback produced by operating Sodium-cooled Fast Reactors (SFRs) has shown the importance of material tribological properties. Where galling or adhesive wear cannot be allowed, hardfacing alloys, known to be galling-resistant coatings, are usually applied on rubbing surfaces.

11p christabelhuynh 29-05-2020 9 0   Download

In this paper, the influences of additive aluminum oxide and hydroxyapatite nanoparticles on the mechanical and strength properties of PMMA (including flexural strength, impact strength, surface hardness and shrinkage behavior) is studied experimentally.

10p tohitohi 19-05-2020 41 3   Download

The experimental results indicated that carbon aerogels obtained by using ambient pressure drying showed BET surface area, density, average pore size, total pore volumes in the range of 459.7–522.1 m2 /g, 0.167–0.629 g/cm3 , 19.45 Å, and 0.259 cm3 /g, respectively. The activation process with CO2 was influence to properties of carbon aerogels and it can improve the surface area reach about 779 m 2 /g. Thus, depending on the applications, carbon aerogels can be synthesized at different conditions.

9p thithizone 16-07-2019 19 0   Download

The objectives of the thesis: Study on materials fabrication technology; structural - photocatalytic properties of TiO2 material, and TiO2 as the nanostructured variant. On the basis of such material system, the systematic and quantitative study on hydrophilicity or, in other words, the study of surface energy of material systems under Exciation of UV light radiation. Further clarification of the correlation between photocatalytic activity, self-cleaning and hydrophobicity of TiO2 nanostructured materials.

32p xacxuoc4321 09-07-2019 30 5   Download

Properties of materials, classes of materials used in medicine,... As the main contents of the lectures "Biomaterials". Invite you to consult for additional documents for the academic needs and research.

21p thangdambme 23-10-2015 46 3   Download

The Elastomeric Alloy (EA) materials based on polypropylene (PP) and Vietnam waste Rubber Powder (RP) has been prepared in internal mixer of Haake in melting state with peroxide initiator. Dynamically stabilizing process at presence of radical donor and acceptor systems has leaded to form chemical bonds on the surface between two phases of surspending rubber powder and PP matrix and then to form intermediate phase surrounding Rubber Particles and making EA higher dense than that of materials by simple mixing RP and PP without networking.

5p uocvong03 24-09-2015 32 6   Download

Two chemical treatments were applied to jute fibers to create a better bonding of fiber to resin in natural composite materials. The jute fibers have been treated with hydroxide potassium (KOH) and a bleaching agent, canxi hypochlorite (Ca(OCl)2.4H2O), in varying periods. Characterization techniques such as FT-IR, SEM were used to evaluate the effect of chemical treatments on fiber structure. After treatment the surface topography of jute was clean and microfibrils were revealed, these lead to an enhancement in mechanical properties and interfacial strength between jute fiber and PP.

8p uocvong01 24-09-2015 71 7   Download