![](images/graphics/blank.gif)
Cutting parameters
-
Cutting condition is a pivotal factor affecting cutting performance in the turning process, especially in marine engineering, where materials must withstand the challenges of maritime environments. This study presents an experimental investigation of the impact of cutting process parameters on surface roughness, Vicker hardness, and cutting temperature in the turning of C45 steel, a critical material for marine applications.
7p
vijaychest
24-04-2024
10
3
Download
-
“SKD-61 steel finds extensive application in various sectors, including the marine industry where materials must withstand harsh aquatic conditions. In this study, we employ the Grey-Taguchi approach to optimize surface roughness (Ra), cutting force (Fc), and material removal rate (MRR) when hard-milling SKD-61 steel in pure minimum quantity lubrication (MQL) and nanofluid MQL environments, aligning with the demands of marine engineering
5p
vijaychest
24-04-2024
3
2
Download
-
Ebook "Fluorescent proteins II: Application of fluorescent protein technology" highlights the physicochemical and biophysical aspects of fluorescent protein technology beyond imaging. It is tailored to meet the needs of physicists, chemists and biologists who are interested in the fundamental properties of fluorescent proteins, while also focussing on specific applications. The implementations described are cutting-edge studies and exemplify how the physical and chemical properties of fluorescent proteins can stimulate novel findings in life sciences.
287p
manmanthanhla0201
26-02-2024
2
1
Download
-
This paper presents the survey results of the relationship between the value of cutting force and the tool flank wear with the cutting parameters in dry turning SKD11 steel with a hardness above 54HRC. With the aim of surveying the change in cutting force and flank wear, each experiment was carried out with several successive cuts until the cutting tool was destroyed.
8p
vishekhar
25-10-2023
6
3
Download
-
Turning is a traditional and widely used machining process in the manufacturing industry. The finished surface quality is one of the most important factors in determining the quality of the product and the effectiveness of the machining process.
8p
viisac
15-09-2023
8
3
Download
-
This paper introduces some traditional and modern cutting parameters optimization (CPO) methods, specifically applied for the Ti-6Al-4V alloy, the most common material in the Ti-alloys, that also belong to the group of typically difficult-to-machine materials.
17p
viengels
25-08-2023
9
3
Download
-
Laser technology provides advantages in cutting complex geometries, stable quality and possibility to utilize fabric and leather materials in economically best way. Constant quality is important in industrial processes of laser technology cutting. Additionally, laser technology is very flexible in terms of geometries such as complex geometries, individual parts and small scale products.
5p
vifriedrich
25-08-2023
6
2
Download
-
The effect of machining parameters on the surface roughness in dry-turning Ti6Al4V alloy using an experimental design method was investigated. A mathematical equation based on the response surface methodology was established to fully understand the influence of machining parameters (cutting speed, feed rate, and depth of cut) on the surface roughness.
9p
viwarmachine
01-07-2023
9
2
Download
-
In this paper, the input parameters of the milling process were studied including cutting speed (V), feed rate (f), and cutting depth (t). The Taguchi method was first used for experimental design.
8p
viironman
02-06-2023
2
1
Download
-
This paper represents results of applying MCDM technique to select optimal input parameters for wire-cut electrical discharge machining (wire-cut EDM) of 90CrSi tool steel. To solve the MCDM problem, the MARCOS method was utilized, and the Entropy method was used to determine the criteria weights.
6p
viironman
02-06-2023
5
2
Download
-
The findings of a study on the application of the MCDM technique to select the best input parameters in wire-cut electrical discharge machining (wire-cut EDM) 90CrSi tool steel are presented in this paper.
7p
viwmotors
02-12-2022
10
4
Download
-
In this paper, machining test in lathe machine is used to check the characteristics of damped drilling tool and damped clamp tool. The testing results are then compared with those of conventional drilling tool and clamp to see the differences.
5p
vichristinelagarde
04-07-2022
11
1
Download
-
Results of the present investigation demonstrate that: (1) friction modeling at the tool-chip interface has a remarkable influence on the numerical simulations of machining; (2) reliability of the friction parameters is substantially interrelated with the choice and reliability of the constitutive model parameters. As a result of this work, the error of force prediction in meshfree cutting simulations can be significantly reduced by adopting an enhanced friction model.
22p
guernsey
28-12-2021
16
0
Download
-
Building a model, setting up a system of dynamic equations of the circular saw cutting bamboo, solving the dynamic equations, from which to calculate and determine some reasonable kinetic and dynamic parameters of the circular saw to improve productivity and cutting surface quality
26p
closefriend09
16-11-2021
12
4
Download
-
The article introduces research results in order to propose some reasonable technological parameters when slicing Betula anoides wood by VS-10 slicing machine manufactured by Taiwan, with two criteria are high quality and low cost.
9p
retaliation
18-08-2021
9
2
Download
-
In this research, the influence of the cutting parameters including cutting speed, feed rate and cutting depth on the flank wear and surface roughness was analyzed by using 2k experimental model with some center points. The results investigated that the feed rate is the most significant parameter effecting on the surface roughness in the machining process and the cutting speed strongly affects on the flank wear in the hard turning of sintered tungsten carbide using CBN inserts.
7p
nguaconbaynhay12
13-06-2021
13
1
Download
-
In this paper, the steel wire will be used to cut AAC. Three parameters must be determined to find optimal ones. Experiments will be done with a cutting machine in which the steel wires were fixed on a steel frame moving forward and backward. When the parameters said above are measured, the statistical data will be found. Based on them, the optimal parameters will be shown.
8p
nguaconbaynhay12
13-06-2021
13
1
Download
-
This paper studied the relationship between the cutting force, surface roughness and chip shrinkage coefficient through the affect of cutting parameters, i.e., cutting speed, feed rate and uncut chip thickness. Experimental results of the chip shrinkage coefficient, cutting force and surface roughness at various cutting parameter values for high-speed milling of A6061 aluminum alloy were presented in this study. The results show that the cutting force and surface roughness can be derived based on the relationships with chip shrinkage coefficient.
5p
cothumenhmong11
10-05-2021
8
2
Download
-
The study was carried out to observe the effect of post harvest application of sucrose on extension of vase life of cut rose cv. Tajmahal. The data was recorded on the physical and physiological parameters on every alternate day. The flowers were held in different concentrations of sucrose solutions with flowers harvested at two stages i.e. tight bud stage and first petal unfurl stage.
13p
trinhthamhodang11
27-04-2021
13
2
Download
-
Hence, the parameters that should be considered for the performance evaluation of detopping unit are forward speed of the unit, peripheral speed of detopping unit and type of the material that cuts the onion leaves.
8p
caygaocaolon11
21-04-2021
6
1
Download
CHỦ ĐỀ BẠN MUỐN TÌM
![](images/graphics/blank.gif)