Cyclic loading

In this paper, the continuous stiffness measurement (CSM) indentation is employed to investigate fatigue mechanical properties of structural steel under cyclic loading. For this purpose, several representative analytical approaches were introduced to estimate the basic mechanical properties including Young’s modulus and indentation hardness from the characteristics of the loading/unloading curves.

11p vifilm 24-09-2024 2 1   Download

The modulus reduction and damping curves represent the nonlinear behavior of soil under cyclic load. In the literature, those curves were produced from lab tests of soil at particular confining stresses. This study developed a set of parameters that can be used to normalize the modulus reduction and damping curves to be stress-independent.

16p vifilm 24-09-2024 2 2   Download

This paper presents a numerical analysis of the seismic behavior of square concrete filled steel tubular (CFST) columns. Finite element analysis (FEA) models in ABAQUS software were used to simulate a series of columns subjected to axial compression and cyclic lateral loading.

14p vifilm 24-09-2024 2 1   Download

Mechanical behaviour of bituminous mixtures is characterized by the great thermal sensitivity and the large viscous effects. This paper focuses on the linear viscoelastic (LVE) behaviour of bituminous mixtures that is considered for pavement design.

10p vifilm 24-09-2024 1 1   Download

This study investigates the performance of prototype U-FREIs under cyclic loading by both experiments and FE analysis. In experiments, four prototype specimens with the same sizes in plan and two different values of shear modulus are produced, and then the characteristic properties including the horizontal stiffness as well as the energy dissipation capacity and the equivalent viscous damping are assessed.

10p viyoko 24-09-2024 2 1   Download

This study investigated the creep rate for OC clay under plain strain condition through laboratory tests, and a new simple empirical correlation between the creep rate and the degree of overconsolidation and principal stress ratio was proposed.

12p vifaye 20-09-2024 2 1   Download

In this study, the evolution of the dislocation cell structure and variation of mechanical properties of structural steel under low-cycle fatigue were studied using the indentation experiment, optical microscope, and transmission electron microscope examinations.

13p viyoko 20-09-2024 5 1   Download

In this study, a methodology was created to evaluate the values of the yield stress of materials based on the grain boundary strengthening equation. This method was constructed by observing the average grain size and determining the mechanical properties of three microstructural phases in the weld zone (i.e. based metal, heat-affected zone, and weld metal).

15p vifaye 20-09-2024 1 1   Download

In this study, in-vitro experiments were performed using a total of 24 porcine motion segments. The harvested specimens were assigned to prolong and 2 different cyclic loadings. Both disc deformations and water contents were measured to investigate how the mode and rate of loading affect the response of intervertebral disc.

8p tohitohi 19-05-2020 8 1   Download

The fatigue failure around rail-end-bolt holes is particularly dangerous since it leads to derailment of trains and consequently to inevitable accidents. It is well-known that the fatigue life of structural holed components, subjected to cyclic load, can be increased by generating compressive hoop stresses around the holes.

18p tohitohi 19-05-2020 16 0   Download

Tuyển tập các báo cáo nghiên cứu về y học được đăng trên tạp chí y học General Psychiatry cung cấp cho các bạn kiến thức về ngành y đề tài: Long-term cyclical in vivo loading increases cartilage proteoglycan content in a spatially specific manner: an infrared microspectroscopic imaging and polarized light microscopy study...

8p thulanh13 14-10-2011 36 2   Download

Metal cutting puts extreme demands on the tool and tool material through conditions of high forces, high contact pressures, high temperatures, and intense chemical attack by difficult to cut work materials. In addition, the tool geometry and cutting conditions in terms of sharp edges, cyclic engagement and presence of cutting fluid will add to the severity. Most often cutting tools are used close to their ultimate resistance against these loads, especially to the limiting thermal and mechanical stresses. ...

14p cuunien 20-12-2010 114 17   Download