Thermal load

Mechanical behaviour of bituminous mixtures is characterized by the great thermal sensitivity and the large viscous effects. This paper focuses on the linear viscoelastic (LVE) behaviour of bituminous mixtures that is considered for pavement design.

10p vifilm 24-09-2024 1 1   Download

The study results for dynamic response of PFGCP present the effect of geometrical ratio, elastic foundations: Winkler foundation and Paskternak foundation; loads: mechanical load and thermal load; and the material properties and distribution type of porosity. The results are shown numerically and are determined by using Galerkin methods and Fourth-order Runge-Kutta method.

21p tamynhan6 14-09-2020 22 3   Download

This paper presents an analytical and a numerical thermomechanical investigation of a thick-walled cylinder made of the functionally graded materials (FGMs). The hollow cylinder is subjected to a pressure and a thermal load and the properties of this material are varying across the thickness from the inner face that is a ceramic to the outer one which is a metal.

8p tohitohi 19-05-2020 11 0   Download

This thesis aims to develop finite element models for studying vibration of FGM porous beams in thermal environment under moving loads. Both analytical method and finite element analysis are employed in the thesis. The analytical method is used to derive equations of motion for the beam, and the finite element method is then employed to solve the governing equations and to determine the dynamic characteristics of the beams.

28p xacxuoc4321 09-07-2019 37 7   Download

The objective of the thesis: Establishing thermal models of single-node, two-node and many-node associated with different thermal loading models acting on a small satellite in Low Earth Orbit. Finding analytical solutions of equations of thermal balance for small satellites by the dual criterion equivalent linearization method.

27p xacxuoc4321 08-07-2019 36 7   Download

Thiol-functionalized SBA-15 silicas have been directly synthesized by cocondensation of tetraethyl orthosilicate (TEOS) and 3-(trimethoxysilyl)-1-propanolthiol (TSPT) under hydrothermal condition. Mesoporous structure was obtained after the surfactant removal by Soxhlet and reflux ethanol extraction. These materials were characterized by means of powder X-ray diffraction, isotherms of nitrogen adsorption/desorption, thermal analysis, infrared spectroscopy and energy-dispersive X-ray spectroscopy.

9p thiendiadaodien_9 04-03-2019 24 0   Download

The article will research a lander flying into the atmosphere with flow velocity constraint, i.e. the total load by means of minimizing the total thermal energy at the end of the landing process. The lander’s distance at the last moment depends on the variables selected from the total thermal energy minima.

8p dieutringuyen 07-06-2017 21 2   Download

I. Introduction An important aspect of nuclear reactor core analysis involves the determination of the optimal coolant flow distribution and pressure drop across the reactor core. On the one hand, higher coolant flow rates will lead to better heat transfer coefficients and higher Critical Heat Flux (CHF) limits. On the other hand, higher flows rates will also in large pressure drops across the reactor core, hence larger required pumping powers and larger dynamic loads on the core components.

259p giotletinh_hd2009 20-04-2013 91 19   Download

Metal cutting puts extreme demands on the tool and tool material through conditions of high forces, high contact pressures, high temperatures, and intense chemical attack by difficult to cut work materials. In addition, the tool geometry and cutting conditions in terms of sharp edges, cyclic engagement and presence of cutting fluid will add to the severity. Most often cutting tools are used close to their ultimate resistance against these loads, especially to the limiting thermal and mechanical stresses. ...

14p cuunien 20-12-2010 114 17   Download

The TPIC6B595 is a monolithic, high-voltage, medium-current power 8-bit shift register designed for use in systems that require relatively high load power. The device contains a built-in voltage clamp on the outputs for inductive transient protection. Power driver applications include relays, solenoids, and other mediumcurrent or high-voltage loads.

10p thevan36 12-12-2010 220 14   Download