Performance optimization

Optimum Flight Trajectories for Terrain Collision AvoidanceThe objective of this research is to introduce a new methodology that computes optimal escape trajectories within a three dimensional digital terrain. It has been established that conducting a pull up manoeuvre may not always be the best option for a pilot to salvage the aircraft in the case of an imminent collision. To prove this further, several simulations were conducted which shows that performing a lateral turn can produce safer trajectories in comparison to a vertical pull up.

155p runthenight07 01-03-2023 7 3   Download

The main objective of this research is to optimize the design of the Tunnel kiln for efficient fuel usage. To achieve that, the temperature distribution from the simulation needs be matched with the desired Tunnel kiln curve found in industry. This objective can be achieved by CFD simulation where temperature, velocity and emission distributions inside the Tunnel kiln can be obtained. Generated temperature distribution can be matched with the industrial curve and by interpreting the curve, efficient design can be suggested.

115p runthenight07 01-03-2023 9 3   Download

Model Predictive Control (MPC) refers to a class of algorithms that optimize the future behavior of the plant subject to operational constraints. The merits of the class algorithms include its ability to handle imposed hard constraints on the system and perform on-line optimization. This thesis investigates design and implementation of continuous time model predictive control using Laguerre polynomials and extends the design approaches proposed in to include intermittent predictive control, as well as to include the case of the nonlinear predictive control.

162p runthenight07 01-03-2023 9 4   Download

The main focus of this thesis is on the application of a model predictive control (MPC) method to devise an ABS for a BBW vehicle. Unlike the traditional ABS control algorithms which are based on a trial and error method, the MPC based ABS algorithm aims to utilizes the behaviour of the model to optimize the wheel slip dynamics subject to system constraints. Performance of the proposed wheel slip controller is validated through Software-in-the-Loop (SiL) and Hardware-inthe-Loop (HiL) simulation.

136p runthenight07 01-03-2023 9 3   Download

The thesis is performed theoretically and experimentally. The theoretical studies on the dynamics of the single short pulse emission using transient cavity method and narrow linewidth and tunable wavelength generation using Littrow grating configuration were performed. On the other hand, the experimental investigations were carried out Experimental research was carried out based on the optimal results obtained by the theoretical studies.

27p beloveinhouse01 15-08-2021 28 4   Download

It is impossible to find an optimal algorithm that can reduce time and memory complexities with best detection performance. These aspects are always in conflict with each other. Thus, in each chapter, we will propose algorithms to solve each problem quite independently.

26p larachdumlanat129 20-01-2021 32 5   Download

The objective of this dissertation is to investigate that whether the investors can improve the performance of minimum – variance optimized portfolios by altering the estimators of covariance matrix input. Besides, based on the results of out – of – sample portfolio performance metrics, the dissertation is going to select the suitable estimators of covariance matrix for portfolio optimization on Vietnam stock market.

129p mmlemmlem_124 22-12-2020 11 2   Download

The research objective of the thesis is to consider how the change of covariance matrix factor will affect the results of portfolio selection and through that to find out whether investors have Is it possible to improve portfolio performance by adjusting the covariance matrix in the optimized model with the smallest variance.

55p mmlemmlem_124 22-12-2020 11 3   Download

Study on fabrication proton exchange membrane fuel cell (PEMFC). Characteristics and selection of the optimal catalyst material and composition for the catalyst layer in membrane electrodes assembly (MEA) and to evaluate influence of manufacturing technological parameters on MEA properties and from that basis master core technology to develop MEA manufacturing process.

28p trinhthamhodang7 31-08-2020 22 2   Download

One of the important contributions of this thesis is that a hierarchical MEMS design synthesis and optimization process have been developed for and validated by the design of a specific structure of MEMS based accelerometer.

126p tamynhan0 04-07-2020 14 6   Download

We propose here to implement an optimization methodology of the blankets design with regards to various parameters such as the local spectrum or the mass to be loaded, with the objective of minimizing the final neutron source of the spent assembly while maximizing the transmutation performances of the blankets.

9p christabelhuynh 30-05-2020 11 0   Download

In this paper, a simplified methodology for the design of targets is coupled with a method for the optimization of transmutation which takes into account both transmutation performances and fuel cycle impacts. The uncertainties and performances of this methodology are evaluated and shown to be sufficient to carry out scoping studies.

12p christabelhuynh 29-05-2020 13 3   Download

This paper presents an ‘ex ante’ decision support tool to evaluate the economic and ecologic impacts of shippers’ horizontal collaboration in urban freight delivery.

18p tohitohi 22-05-2020 21 1   Download

Tiểu luận với các nội dung: cực đại lượng điền lớp LTL, cực tiểu tổng số rơ-mooc được sử dụng, cực tiểu thời gian thông lượng SKU, tối ưu cho lớp điền LTL, tối ưu 4 yếu tố trên với trọng số như nhau...

10p moneylady123 10-12-2019 50 11   Download

The overall objective is based on the fundamental theories of capital structure and empirical research on capital structure and financial performance of the firm, whereby the author develops and analyzes the relationship between capital structure and financial performance. It then determines the optimal debt threshold for the Tourism and travel companies (TTCs) of Hue City.

29p quenchua 28-09-2019 47 3   Download

(BQ) The present work deals with the comparison of the MRR for EN19 and EN41 material in a die sinking EDM machine. The various input factors like Pulse ON time, Pulse OFF time, Discharge current and voltage were considered as the input processing parameters, while the MRR is considered as the output. Optimization using Taguchi method was performed to predict the best combination of inputs towards maximum output.

7p xuanphuongdhts 27-03-2017 37 2   Download

Module 6: Managing and monitoring domain name system. This module provides you with the knowledge and skills to manage and monitor DNS servers to ensure that they are functioning properly and to optimize network performance.

20p nomoney2 10-02-2017 42 3   Download

An optogenetic upgrade for the tet - OFF system fused the inhibitor to the blue light-responsive B-LID degron and optimized the performance of this construct with regard to the number of Med25VBD repeats. This approach resulted in an optogenetic upgrade of the popular Tet-OFF (TetR-VP64, tetO7-PhCMVmin)  system  that  allows tunable, blue light-inducible gene expression in HEK-293T  cells.

5p thuyancn 01-06-2015 30 5   Download

Trans-splicing group I ribozymes have been introduced in order to mediate RNA reprogramming (including RNA repair) of therapeutically relevant RNA transcripts. Efficient RNA reprogramming depends on the appropri-ate efficiency of the reaction, and several attempts, including optimization of target recognition and ribozyme catalysis, have been performed.

12p dell39 27-03-2013 33 3   Download

For 30 years, the field of medical device technology has struggled to identify the specifications for optimal biocompatibility. For the vast majority of devices, clinical experience has eventually confirmed that the best performance is achieved when biocom-patibility is equated with biological safety that is materials are selected on the basis of maximizing bioinertness and minimizing toxicity and irritation.

7p inspiron33 26-03-2013 52 5   Download