Pulse on time

This article presents a study on the investigation of the effects of the input parameters on the cutting speed in machining 90CrSi tool steel using wire cut electrical discharge machining (EDM).

6p lucastanguyen 01-06-2020 41 2   Download

(BQ) In this research work two different materials have been used as work pieces. These EN8 and D3 steel materials have been machined in an Electrical discharge machine which has wide application in Industry fields. The important process parameters that have been selected are peak current, pulse on time, die electric pressure and tool diameter. The outputs responses are material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR).

11p xuanphuongdhts 27-03-2017 48 2   Download

(BQ) In this paper, working current, working voltage, oil pressure, spark gap Pulse On Time and Pulse Off Time on Material Removal Rate (MRR) and Surface Finish (Ra) has been studied. Empirical models for MRR and Ra have been developed by conducting a designed experiment based on the Grey Relational Analysis. Genetic Algorithm (GA) based multi-objective optimization for maximization of MRR and minimization of Ra has been done by using the developed empirical models. Optimization results have been used for identifying the machining conditions.

10p xuanphuongdhts 27-03-2017 42 2   Download

(BQ) This paper is devoted to a study of the influences of EDM parameters on surface roughness for machining of 40CrMnNiMo864 tool steel (AISI P20) which is widely used in the production of plastic mold and die. The selected EDM parameters were pulsed current (8, 16 and 24 A), pulse time (2, 3, 4, 6, 12, 24, 48 and 100 s) and pulse pause time (2 and 3s). It was observed that surface roughness of workpiece and electrode were influenced by pulsed current and pulse time, higher values of these parameters increased surface roughness.

4p xuanphuongdhts 27-03-2017 52 4   Download

(BQ) This study was made only for the finish stages and has been carried out on the influence of five design factors: intensity supplied by the generator of the EDM machine (I), pulse time (ti), duty cycle (η), open-circuit voltage (U) and dielectric flushing pressure (P), over the two previously mentioned response variables. This has been done by means of the technique of design of experiments (DOE), which allows us to carry out the above-mentioned analysis performing a relatively small number of experiments.

8p xuanphuongdhts 27-03-2017 56 2   Download

(BQ) Surface integrity and dimensional accuracy remain critical concern in Electrical Discharge Machining (EDM). The current research work aims at investigating the influence of various EDM process parameters like pulse current (Ip), pulse-on time (Ton), tool work time (Tw) and tool lift time (Tup) on various aspects of surface integrity like white layer thickness (WLT), surface crack density (SCD) and surface roughness (SR). The dimensional accuracy, characterized by over cut (OC), has also been studied in the similar way.

13p xuanphuongdhts 27-03-2017 47 2   Download

(BQ) The adequate selection of manufacturing conditions is one of the most important aspects to take into consideration in the die-sinking electrical discharge machining (EDM) of conductive ceramics, as these conditions are the ones that are to determine such important characteristics as: surface roughness, electrode wear (EW) and material removal rate, among others. In this work, a study was carried out on the influence of the factors of intensity (I), pulse time (ti) and duty cycle (η) over the listed technological characteristics.

7p xuanphuongdhts 27-03-2017 38 2   Download

(BQ) The present work deals with the comparison of the MRR for EN19 and EN41 material in a die sinking EDM machine. The various input factors like Pulse ON time, Pulse OFF time, Discharge current and voltage were considered as the input processing parameters, while the MRR is considered as the output. Optimization using Taguchi method was performed to predict the best combination of inputs towards maximum output.

7p xuanphuongdhts 27-03-2017 37 2   Download

(BQ) The article presents an idea about the effect of the various input process parameters like Pulse ON time, Pulse OFF time, Discharge Current and Voltage over the Surface Roughness for an EN41 material. Here, 5 different output parameters concerned with surface roughness like Ra, Rq, Rsk, Rku and Rsm are taken and optimized accordingly, using the Grey-Taguchi method.

8p xuanphuongdhts 27-03-2017 61 4   Download

Hindawi Publishing Corporation EURASIP Journal on Advances in Signal Processing Volume 2008, Article ID 468390, 9 pages doi:10.1155/2008/468390 Research Article A Framework for Automatic Time-Domain Characteristic Parameters Extraction of Human Pulse Signals Pei-Yong Zhang1 and Hui-Yan Wang2 1 Institute 2 College of VLSI Design, Zhejiang University, Hangzhou 310027, China of Computer Science and Information Engineering, Zhejiang Gongshang University, Hangzhou 310018, China Correspondence should be addressed to Hui-Yan Wang, cederic@mail.zjgsu.edu.

9p dauphong18 24-02-2012 53 5   Download

Tuyển tập báo cáo các nghiên cứu khoa học quốc tế ngành y học dành cho các bạn tham khảo đề tài: Evaluation of adaptation to visually induced motion sickness based on the maximum cross-correlation between pulse transmission time and heart rate

6p panasonic01 12-12-2011 45 5   Download