The electrical discharge machining

This paper shows a study on the influences of the process parameters of wire cut electrical discharge machining (WEDM) on the surface roughness in machining 90CrSi tool steel.

6p lucastanguyen 01-06-2020 53 3   Download

This article presents a study on the investigation of the effects of the input parameters on the cutting speed in machining 90CrSi tool steel using wire cut electrical discharge machining (EDM).

6p lucastanguyen 01-06-2020 41 2   Download

The development of techniques that allow producing high-finish surfaces of geometrically-complex parts of difficult-to-machine materials by electrical discharge machining (EDM) is an emerging research area. The aim of this work is to study the application of electrolytic-plasma polishing technique for the high-quality surface finish of the parts obtained by EDM process.

6p tohitohi 19-05-2020 15 3   Download

(BQ) In this research work two different materials have been used as work pieces. These EN8 and D3 steel materials have been machined in an Electrical discharge machine which has wide application in Industry fields. The important process parameters that have been selected are peak current, pulse on time, die electric pressure and tool diameter. The outputs responses are material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR).

11p xuanphuongdhts 27-03-2017 48 2   Download

(BQ) Electrical discharge machining (EDM) is a widespread process which works very effectively in machining of difficult-to-cut materials and alloys in die and aerospace industries with high dimensional accuracies. However, this capability could be deteriorated due to electrode wear leading to decrease of process productivity. In this study, the effect of machining parameters of EDM process including on-time, current, voltage, the engaging time between workpiece and electrode, and pre-EDM roughing on electrode wear were experimentally investigated.

4p xuanphuongdhts 27-03-2017 49 2   Download

(BQ) The study sheds light on the powerful learning capability of ANFIS models and its superiority over the conventional polynomial models in terms of modelling complex non-linear machining processes

15p xuanphuongdhts 27-03-2017 41 2   Download

(BQ) This paper reviews the research trends in EDM on ultrasonic vibration, dry EDM machining, EDM with powder additives, EDM in water and modeling technique in predicting EDM performances

15p xuanphuongdhts 27-03-2017 47 5   Download

(BQ) From the experimental results, it has been found that the electrical conductivity of the tool electrode has the most influencing nature on the machining characteristics in EDM process. The optimal combination of the input process parameters has been obtained using Taguchi-grey relational analysis.

8p xuanphuongdhts 27-03-2017 68 3   Download

(BQ) The present study discusses about having an overview of the EDM process, modeling of process parameters, and influence of process parameters such as input electrical variables, pulse shape, and discharge energy on performance measures such as material removal rate, surface roughness and electrode wear rate.

8p xuanphuongdhts 27-03-2017 52 2   Download

(BQ) This paper is devoted to a study of the influences of EDM parameters on surface roughness for machining of 40CrMnNiMo864 tool steel (AISI P20) which is widely used in the production of plastic mold and die. The selected EDM parameters were pulsed current (8, 16 and 24 A), pulse time (2, 3, 4, 6, 12, 24, 48 and 100 s) and pulse pause time (2 and 3s). It was observed that surface roughness of workpiece and electrode were influenced by pulsed current and pulse time, higher values of these parameters increased surface roughness.

4p xuanphuongdhts 27-03-2017 49 4   Download

(BQ) The present work is aimed at optimizing the surface roughness of die sinking electric discharge machining (EDM) by considering the simultaneous affect of various input parameters.

9p xuanphuongdhts 27-03-2017 55 2   Download

(BQ) The method of electrical discharge machining (EDM), one of the processing methods based on non-traditional manufacturing procedures, is gaining increased popularity, since it does not require cutting tools and allows machining involving hard, brittle, thin and complex geometry

9p xuanphuongdhts 27-03-2017 53 2   Download

(BQ) The aim of this research is to show the influence of the hardness of the alloy steel on the material removal rate and on the workpiece surface roughness.

5p xuanphuongdhts 27-03-2017 22 2   Download

(BQ) This paper reports an intelligent approach for process modeling and optimization of electric discharge machining (EDM). Physics based process modeling using finite element method (FEM) has been integrated with the soft computing techniques like artificial neural networks (ANN) and genetic algorithm (GA) to improve prediction accuracy of the model with less dependency on the experimental data.

13p xuanphuongdhts 27-03-2017 56 2   Download

(BQ) This paper aims to develop a combination of Taguchi and fuzzy TOPSIS methods to solve multi-response parameter optimization problems in green manufacturing.

5p xuanphuongdhts 27-03-2017 53 3   Download

(BQ) The paper describes the application of the fuzzy logic analysis coupled with Taguchi methods to optimise the precision and accuracy of the high-speed electrical discharge machining (EDM) process. A fuzzy logic system is used to investigate relationships between the machining precision and accuracy for determining the efficiency of each parameter design of the Taguchi dynamic experiments.

10p xuanphuongdhts 27-03-2017 54 3   Download

(BQ) Electrical discharge machining (EDM) is inherently a stochastic process. Predicting the output of such a process with reasonable accuracy is rather difficult.

19p xuanphuongdhts 27-03-2017 42 2   Download

(BQ) In the study, temperature measurements have been made for Ti–6Al–4V workpieces with various duty factors to clarify the essential causes of difficulty in machining titanium alloys and observe the optimal duty factor in terms of productivity and quality.

7p xuanphuongdhts 27-03-2017 49 4   Download

(BQ) Surface integrity and dimensional accuracy remain critical concern in Electrical Discharge Machining (EDM). The current research work aims at investigating the influence of various EDM process parameters like pulse current (Ip), pulse-on time (Ton), tool work time (Tw) and tool lift time (Tup) on various aspects of surface integrity like white layer thickness (WLT), surface crack density (SCD) and surface roughness (SR). The dimensional accuracy, characterized by over cut (OC), has also been studied in the similar way.

13p xuanphuongdhts 27-03-2017 47 2   Download

(BQ)This paper proposes an experimental investigation and optimization of the various machining parameters for the electrical discharge machining (EDM) processes on Inconel 718 super alloy using a multi objective particle swarm optimization (MOPSO) algorithm.

7p xuanphuongdhts 27-03-2017 41 2   Download