Finite element modelling

This study focuses on evaluating short-term deflections of reinforced concrete beams according to the Vietnamese Standard on the Design of Concrete and Reinforced Concrete Structures (TCVN 5574:2018) by comparing them with simulated results obtained from Abaqus software.

9p viengfa 28-10-2024 1 1   Download

Folding plates with wavy shapes made of composite materials have been widely applied, hence designing this type of structure is significant in practice. In this research work, the results of static calculation of the sinusoidal corrugated composite plates will be analyzed.

9p viengfa 28-10-2024 2 1   Download

this paper focuses on the adhesion failure between the asphalt wearing course and the steel plate, and the temperature influence on the mechanical behavior of the orthotropic deck. Orthotropic steel bridge decks (OSBDs) have been widely used in long span bridges with many advantages, however, the long-term performance of the asphalt wearing course is still questionable.

9p vibecca 01-10-2024 2 1   Download

This paper provides the validation of ABAQUS 3D finite element model by the experimental results. Test specimens consist of four specimens of new exterior RCS hybrid joint that the European Project SMARTCOCO investigated with the aim to ease the construction process and avoid additional on-site work.

7p vibecca 01-10-2024 2 1   Download

This study aims to evaluate the allowable bearing capacity of the strip footing subjected to uniform vertical loading. Finite element modeling is implemented to analyze the behavior of soil the ground under the strip footing.

4p vibecca 01-10-2024 2 0   Download

This paper presents a numerical modeling of RC shear walls using SSI3D finite element program. The objective of this research is to develop the full-scale model lab test of reinforced concrete (RC) shear wall. The wall is subjected to axially and laterally monotonic loading up to failure.

4p vibecca 01-10-2024 3 1   Download

In this study, a numerical model was developed to simulate the mechanical behavior of an orthotropic steel bridge deck (OSBD) strengthened with UHPC under localized loads based on the five-point bending beam test configuration.

10p vibecca 01-10-2024 2 0   Download

A finite element model using a multi-fiber approach is proposed in this paper for the analysis of reinforced concrete (RC) members using fiber-reinforced polymer (FRP) reinforcements, with a specific focus on the effect of pure torsion. The main objective of this study is to develop a numerical finite element model to predict the behavior of RC beams with FRP reinforcement under pure torsional effects.

14p vibecca 01-10-2024 3 2   Download

In this article, the authors have researched and evaluated the effectiveness of load transfer according to deflection through the application of the 3D finite element method. The model utilizes material parameters and actual airport hard pavement structures and calculates for many types of aircraft commonly operating in Vietnam.

12p viyoko 01-10-2024 5 1   Download

In this study, it is split into two main steps. First, an analytical design is proposed to define the desired parameters with affects of different flux air gaps. Then, a finite element approach is developed to simulate inductances, leakage and fringing fluxes, magnetic flux density and electromagnetic force with different flux air gaps.

6p viyoko 01-10-2024 2 1   Download

A hybrid analytical-numerical solution is proposed to solve the problem of a laterally loaded pile with a circular cross-section in multilayered soils. In the pile-soil model, the lateral load is located at the pile head including both lateral force and bending moment. The single pile is considered as a beam on elastic foundation while shear beams model the soil column below the pile toe.

14p vifilm 24-09-2024 6 1   Download

This study shows that the stirrups corrosion should receive more attention in the serviceability limit state due to its considerable effect on flexural behavior. Based on a parametric study, it shows that the effect of the crosssection loss of tension reinforcements on the load-carrying capacity of the corroded beam is more significant than the bond strength reduction.

14p vifilm 24-09-2024 3 1   Download

The modulus reduction and damping curves represent the nonlinear behavior of soil under cyclic load. In the literature, those curves were produced from lab tests of soil at particular confining stresses. This study developed a set of parameters that can be used to normalize the modulus reduction and damping curves to be stress-independent.

16p vifilm 24-09-2024 3 2   Download

A big question in the numerical approaches for the mechanical behavior of the textile-reinforced concrete (TRC) composite under tensile loading is how to model the cracking of the cementitious matrix. This paper presents numerical results of 3-D modeling of TRC composite in which the non-linear behavior model was used by considering the cracking for the cementitious matrix.

12p vifilm 24-09-2024 1 1   Download

This paper presents a numerical analysis of the seismic behavior of square concrete filled steel tubular (CFST) columns. Finite element analysis (FEA) models in ABAQUS software were used to simulate a series of columns subjected to axial compression and cyclic lateral loading.

14p vifilm 24-09-2024 2 1   Download

This paper summarizes the basic principle of FEM and DEM, then reviews a number of possible direct coupling strategies between FEM and DEM together with potential applications in civil engineering. The second objective is to develop a model that combines these two above mentioned methods in a multi-scale approach.

12p vifilm 24-09-2024 2 1   Download

This study presents a unified approach to simulate the behavior of rectangular concrete-filled steel stub columns incorporating high strength and ultra-high strength materials subjected to concentric axial compression.

14p vifilm 24-09-2024 6 1   Download

This paper addresses the strength and deformation capacity of slender columns retrofitted by externally bonded Carbon Fiber-Reinforced Polymers (CFRP) subjected to seismic loading. The behaviour of RC columns depending on the CFRP confinement (carbon CFRP jacket) and on flexural reinforcement (carbon plates) was analysed by a nonlinear finite element method based on multilayer shell element and multifiber beams with plasticity and damage models.

7p viyoko 24-09-2024 2 1   Download

A fuzzy finite element approach for static analysis of laterally loaded pile in multi-layer soil with uncertain properties is presented. The finite element (FE) formulation is established using a beam-on-two-parameter foundation model.

9p viyoko 24-09-2024 4 0   Download

This study proposes an alternative approach based on the deep learning paradigm working in a complementary way with conventional methods such as the finite element method for quickly forecasting the responses of structures under random wind loads with reasonable accuracy.

11p vifaye 20-09-2024 3 1   Download