Electrical process parameters

This paper shows a study on the influences of the process parameters of wire cut electrical discharge machining (WEDM) on the surface roughness in machining 90CrSi tool steel.

6p lucastanguyen 01-06-2020 53 3   Download

This article presents a study on the investigation of the effects of the input parameters on the cutting speed in machining 90CrSi tool steel using wire cut electrical discharge machining (EDM).

6p lucastanguyen 01-06-2020 41 2   Download

(BQ) In this research work two different materials have been used as work pieces. These EN8 and D3 steel materials have been machined in an Electrical discharge machine which has wide application in Industry fields. The important process parameters that have been selected are peak current, pulse on time, die electric pressure and tool diameter. The outputs responses are material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR).

11p xuanphuongdhts 27-03-2017 48 2   Download

(BQ) Electrical discharge machining (EDM) is a widespread process which works very effectively in machining of difficult-to-cut materials and alloys in die and aerospace industries with high dimensional accuracies. However, this capability could be deteriorated due to electrode wear leading to decrease of process productivity. In this study, the effect of machining parameters of EDM process including on-time, current, voltage, the engaging time between workpiece and electrode, and pre-EDM roughing on electrode wear were experimentally investigated.

4p xuanphuongdhts 27-03-2017 49 2   Download

(BQ) From the experimental results, it has been found that the electrical conductivity of the tool electrode has the most influencing nature on the machining characteristics in EDM process. The optimal combination of the input process parameters has been obtained using Taguchi-grey relational analysis.

8p xuanphuongdhts 27-03-2017 68 3   Download

(BQ) The present study discusses about having an overview of the EDM process, modeling of process parameters, and influence of process parameters such as input electrical variables, pulse shape, and discharge energy on performance measures such as material removal rate, surface roughness and electrode wear rate.

8p xuanphuongdhts 27-03-2017 52 2   Download

(BQ) The method of electrical discharge machining (EDM), one of the processing methods based on non-traditional manufacturing procedures, is gaining increased popularity, since it does not require cutting tools and allows machining involving hard, brittle, thin and complex geometry

9p xuanphuongdhts 27-03-2017 53 2   Download

(BQ) This paper aims to develop a combination of Taguchi and fuzzy TOPSIS methods to solve multi-response parameter optimization problems in green manufacturing.

5p xuanphuongdhts 27-03-2017 53 3   Download

(BQ) The paper describes the application of the fuzzy logic analysis coupled with Taguchi methods to optimise the precision and accuracy of the high-speed electrical discharge machining (EDM) process. A fuzzy logic system is used to investigate relationships between the machining precision and accuracy for determining the efficiency of each parameter design of the Taguchi dynamic experiments.

10p xuanphuongdhts 27-03-2017 54 3   Download

(BQ) Electrical discharge machining (EDM) is inherently a stochastic process. Predicting the output of such a process with reasonable accuracy is rather difficult.

19p xuanphuongdhts 27-03-2017 42 2   Download

(BQ) Surface integrity and dimensional accuracy remain critical concern in Electrical Discharge Machining (EDM). The current research work aims at investigating the influence of various EDM process parameters like pulse current (Ip), pulse-on time (Ton), tool work time (Tw) and tool lift time (Tup) on various aspects of surface integrity like white layer thickness (WLT), surface crack density (SCD) and surface roughness (SR). The dimensional accuracy, characterized by over cut (OC), has also been studied in the similar way.

13p xuanphuongdhts 27-03-2017 47 2   Download

(BQ)This paper proposes an experimental investigation and optimization of the various machining parameters for the electrical discharge machining (EDM) processes on Inconel 718 super alloy using a multi objective particle swarm optimization (MOPSO) algorithm.

7p xuanphuongdhts 27-03-2017 41 2   Download

(BQ) The adequate selection of manufacturing conditions is one of the most important aspects to take into consideration in the die-sinking electrical discharge machining (EDM) of conductive ceramics, as these conditions are the ones that are to determine such important characteristics as: surface roughness, electrode wear (EW) and material removal rate, among others. In this work, a study was carried out on the influence of the factors of intensity (I), pulse time (ti) and duty cycle (η) over the listed technological characteristics.

7p xuanphuongdhts 27-03-2017 38 2   Download

(BQ) The objective of this paper is to find out the combination of process parameters for optimum surface roughness and material removal rate (MRR) in electro discharge machining (EDM) of EN31 tool steel using artificial bee colony (ABC) algorithm.

11p xuanphuongdhts 27-03-2017 48 2   Download

(BQ) The present work deals with the comparison of the MRR for EN19 and EN41 material in a die sinking EDM machine. The various input factors like Pulse ON time, Pulse OFF time, Discharge current and voltage were considered as the input processing parameters, while the MRR is considered as the output. Optimization using Taguchi method was performed to predict the best combination of inputs towards maximum output.

7p xuanphuongdhts 27-03-2017 37 2   Download

(BQ) The article presents an idea about the effect of the various input process parameters like Pulse ON time, Pulse OFF time, Discharge Current and Voltage over the Surface Roughness for an EN41 material. Here, 5 different output parameters concerned with surface roughness like Ra, Rq, Rsk, Rku and Rsm are taken and optimized accordingly, using the Grey-Taguchi method.

8p xuanphuongdhts 27-03-2017 61 4   Download

(BQ) Electrical Discharge Machining (EDM) is a non-traditional machining process which is more efficient than traditional maching process due to ease of machining of difficult-to-machine materials with complex shapes. EDM is used for machining of toughened and high strength conductive materials which is hard enough to cut by traditional processes.

8p xuanphuongdhts 27-03-2017 41 2   Download

(BQ) Electrical Discharge Machining (EDM) is a non-traditional machining process which has the ability to machine hard, difficult to machine materials and the parts with complex internal shapes by using precisely controlled sparks that occurs between an electrode and a work piece in the presence of a dielectric fluid.

9p xuanphuongdhts 27-03-2017 68 3   Download

(BQ) The newly engineered metal matrix composite (MMC) of aluminium 7075 reinforced with 10 wt% of B4C particles were prepared by stir casting method. Experiments were carried out by adopting face centered central composite design of response surface methodology.

6p xuanphuongdhts 27-03-2017 40 3   Download

(BQ) Electrical Discharge Machining (EDM) is a non-traditional, thermo electrical process, which erodes material from the work piece by a series of discrete sparks between the work and tool electrode immersed in a liquid dielectric medium.

7p xuanphuongdhts 27-03-2017 46 3   Download